ASTM D3376-25 PDF

ASTM D3376-25 PDF

Standard Test Methods of Sampling and Testing Pulps to be Used in the Manufacture of Electrical Insulation

$36.00 $72.00 -50%
Product Code: ASTM D3376
Stock In Stock
Published: 2025
Number of Pages: 10

Available Options

Product Description

Significance and Use
 8.1  The conductivity of the water extract of electrical grade pulp results from electrolytic impurities in the pulp potentially present as ionizable acids, bases, salts, or a combination of these. The presence of electrolytic impurities in electrical insulation is undesirable as they tend to lower insulation resistance and have corrosion-producing tendencies under conditions of applied potential. When comparing test data, note that the extract conductivity of pulps, especially those of high purity, changes with time after manufacturing in some instances. This test is useful for routine acceptance testing, the comparison of different pulps, and research work. 6
 Scope
 1.1  These test methods cover the sampling and testing of cellulosic pulps for use in the manufacture of electrical insulating papers and boards or in the direct application of pulp fibers as insulation to electrical conductors.
 Note 1:   Consider the significance of any one pulp property test method, as set forth herein, with discretion depending on the product made from the pulp.
 1.2  Sections on Reagents, Sampling, and Report are integral parts of each of the individual test methods that follow.
 1.3  Each test method is described as being a measure of either a bulk property of the pulp or a property of a handsheet formed from the pulp.
 1.3.1  Bulk characteristics determinable by these procedures appear in the following sections:
 Procedure
 Sections
 ASTM Method Reference
 TAPPI Method Reference
 Aqueous Extract Conductivity
 8 & 9
 D202
 . . .
 Aqueous Extract pH
 10 & 11
 D202
 . . .
 Aqueous Extractable Acidity-      Alkalinity
 12 & 13
 D202
 . . .
 Analysis of Ash for Cations by      Atomic Absorption Spectrophotometry
 70 – 78
 D1193 & D2576
 . . .
 Ash Content
 79 – 82
 D202
 T 413
 Dirt in Pulp
 40 & 41
 . . .
 T 213
 Fiber Analysis
 23 & 24
 D202 & D1030
 . . .
 Fiber Length of Pulp
 42 & 43
 . . .
 T 232, T 233
 Freeness (Canadian Standard      Freeness)
 53 & 54
 . . .
 T 227
 Kappa Number/Permanganate      Number (Substances Oxidizable      by Permanganate)
 27 & 28
 . . .
 T 236, UM 251
 Laboratory Processing of Pulp      (Beater Method)
 51 & 52
 . . .
 T 200
 Moisture in Pulp
 31 – 33
 . . .
 T 210
 Neutral Aqueous Extractable  Hard-      ness in Pulp
 16 – 22
 D202 , D1126 , &  D2576
 . . .
 Pentosan Content of Pulp
 29 & 30
 . . .
 T 223
 Resistance of Pulp to Disintegration      (Standard RPG)
 44 – 50
 . . .
 T 239, UM 252
 Shive Count
 34 – 39
 . . .
 . . .
 Solvent-Soluble Matter in Pulp
 25 & 26
 D202
 . . .
 Tensile Properties
 65 – 69
 D202
 . . .
 Water-Extractable Chlorides
 14 & 15
 D202
 . . .
 1.3.2  Handsheet characteristics determinable by these procedures appear in the following sections:
 Procedure
 Sections
 ASTM Method Reference
 TAPPI Method Reference
 Air Resistance (Porosity)
 57 & 58
 D202
 T 205
 Apparent Density
 63 & 64
 D202
 T 205
 Bursting Strength
 59 & 60
 D202 & D774/D774M
 T 205
 Folding Endurance (M.I.T.)
 51 & 52
 D202 & D2176
 T 205
 Forming Handsheets for Physical      Tests of Pulp
 55 & 56
 . . .
 T 205
 Tensile Strength
 65 & 66
 D202 & D828
 T 205
 Note 2:   Methods for Ash, Silica, selected cations from Ash, Heat Stability, α, β, and γ Cellulose, Viscosity, Total Chlorine, Tear, and Dissipation Factor and Relative Permittivity, will be considered for addition as methods are developed.
 1.4  The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
 1.5   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
 1.6   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM D3376-25 PDF

ASTM D3376-25 PDF

$36.00 $72.00