ASTM F645-25 PDF

ASTM F645-25 PDF

Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems

$40.00 $80.00 -50%
Product Code: ASTM F645
Stock In Stock
Published: 2025
Number of Pages: 13

Available Options

Product Description

Significance and Use
 4.1  The requirements of this specification are intended to provide information to select, design and install thermoplastic, water-pressure piping systems. Materials covered in this specification are Poly(Vinyl Chloride) (PVC), Chlorinated Poly(Vinyl Chloride) (CPVC) and Polyethylene (PE) plastic pipe fittings.
 Scope
 1.1  This guide is intended for use in the selection, design, and installation of thermoplastic water-pressure piping systems. For specific projects, a thorough review of this guide is recommended for the purpose of selecting specific materials, methods of joining, system design factor, and any special procedures deemed necessary to assure a satisfactory system.
 Note 1:   Comprehensive information on the selection, design, joining, system design factors, installation and special products and piping systems for pressurized water and other specialized applications is available in the Uni-Bell PVC Pipe Association Handbook of PVC Pipe Design and Construction, PPI Handbook of Polyethylene Pipe and from other domestic and International sources such as PE compound and product manufacturers and trade associations.
 1.2  It is recommended that governing codes and project specifications be consulted prior to the use of this guide. Nothing in this guide should be construed as recommending practices or systems at variance with governing codes and project specifications.
 1.3  The pipe, fittings, and joining materials shall meet the requirements of one or more of the following component product standards listed in 1.3.1 through 1.3.4 to the extent applicable. In 1.3.1 , 1.3.2 , and 1.3.4 the pipe standards followed by ( a ) are outside diameter-controlled pipes.
 1.3.1   For poly(vinyl chloride) (PVC) plastic piping components:   Title of Specification
 ASTM Designation
 Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80  and 120 ( a )
 D1785
 Poly(Vinyl Chloride) (PVC) Plastic Pipe (SDR-PR) ( a )
 D2241
 Threaded Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings,  Schedule 80
 D2464
 Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule  40
 D2466
 Socket-Type Poly(Vinyl Chloride) (PVC) Plastic Pipe  Fittings, Schedule 80
 D2467
 Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Pipe  and Fittings
 D2564
 Bell-End Poly(Vinyl Chloride) (PVC) Pipe ( a )
 D2672
 Poly(Vinyl Chloride) (PVC) Plastic Tubing ( a )
 D2740
 Socket-Type Poly(Vinyl Chloride) (PVC) Plastic Line  Couplings
 D3036
 Joints for Plastic Pressure Pipes Using Flexible Elastomeric  Seals
 D3139
 Elastomeric Seals (Gaskets) for Joining Plastic Pipe
 F477
 PVC and ABS Injected Solvent Cemented Plastic Pipe  Joints
 F545
 1.3.2   For Chlorinated Poly(Vinyl chloride) (CPVC) plastic piping components:  
 Title of Specification
 ASTM Designation
 Chlorinated Poly(Vinyl chloride) (CPVC) Plastic Pipe, Schedules 40 and 80 (a)
 F441/F441M
 Chlorinated Poly(Vinyl chloride) (CPVC) Plastic Pipe Fittings, Schedule 80
 F439
 Solvent Cements for Chlorinated Poly(Vinyl chloride) (CPVC) Plastic Pipe and Fittings
 F493
 1.3.3   Standards for polyethylene (PE) plastic piping:  
  ASTM Standard
 Designation
 Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter
 D2239
 Standard Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe
 D2609
 Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing
 D2683
 Standard Specification for Polyethylene (PE) Plastic Tubing
 D2737
 Standard Practice for Underground Installation of Thermoplastic Pressure Piping
 D2774
 Standard Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing
 D3261
 Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter
 D3035
 Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter
 F714
 Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing
 F1055
 Standard Specification for Socket Fusion Tools for Use in Socket Fusion Joining Polyethylene Pipe or Tubing and Fittings
 F1056
 Standard Practice for Electrofusion Joining Polyolefin Pipe and Fittings
 F1290
 Standard Specification for Deformed Polyethylene (PE) Liner
 F1533
 Standard Guide for Construction Procedures for Buried Plastic Pipe
 F1668
 Standard Practice for Field Leak Testing of Polyethylene (PE) and Crosslinked Polyethylene (PEX) Pressure Piping Systems Using Hydrostatic Pressure
 F2164
 Standard Specification for Fabricated Fittings of Butt-Fused Polyethylene (PE)
 F2206
 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
 F2620
 Standard Test Method for Laboratory Testing of Polyethylene (PE) Butt Fusion Joints using Tensile-Impact Method
 F2634
 Standard Practice for Field Leak Testing of Polyethylene (PE) Pressure Piping Systems Using Gaseous Testing Media Under Pressure (Pneumatic Leak Testing)
 F2786
 Standard Specification for Lap-Joint Type Flange Adapters for Polyethylene Pressure Pipe in Nominal Pipe Sizes ¾ in. to 65 in.
 F2880
 Standard Practice for Specimens and Testing Conditions for Testing Polyethylene (PE) Pipe Butt Fusions Using Tensile and Hydrostatic Test Methods
 F2928
 Standard Specification for Billets made by Winding Molten Extruded Stress-Rated High Density Polyethylene (HDPE)
 F3034
 Standard Specification for Metric Outside Diameter Polyethylene (PE) Plastic Pipe (DR-PN)
 F3123
 Standard Practice for Data Recording the Procedure used to Produce Heat Butt Fusion Joints in Plastic Piping Systems or Fittings
 F3124
 Standard Practice for Guided Side Bend Evaluation of Polyethylene Pipe Butt Fusion Joint
 F3183
 Standard Practice for Heat Fusion Equipment (HFE) Operator Qualification on Polyethylene (PE) and Polyamide (PA) Pipe and Fittings
 F3190
 AWWA Standards
 Standards Polyethylene (PE) Pressure Pipe and Tubing, 1/2 in. (13 mm) Through 3 in. (76 mm), for Water Service
 C901
 Polyethylene (PE) Pressure Pipe and Fittings, 4 In. Through 65 In. (100 mm Through 1,650 mm), for Waterworks
 C906
 CSA Standards
 Standards Definitions, general requirements, and methods of testing for thermoplastic pressure piping
 B137.0
 Polyethylene (PE) pipe, tubing, and fittings for cold water pressure services
 B137.1
 1.3.4   For poly(vinyl chloride) (PVC) Plastic Piping Components Issued By the American Water Works Association:  
 C900 Poly(Vinyl Chloride) (PVC) Pressure Pipe,
 4-inch through 12-inch, for Water (a)
 1.3.5  Pipes with wall thicknesses less than 1.50 mm (0.06 in.) are not recommended.
 1.4   Other Joining Devices— Joining devices other than those covered by the listed standards may be selected by the user on the basis of his own engineering evaluation and service experience.
 1.5  The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.
 1.6   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
 1.7   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM F645-25 PDF

ASTM F645-25 PDF

$40.00 $80.00