IEC 60512-23-3-2018 PDF

IEC 60512-23-3-2018 PDF

Connectors for electrical and electronic equipment-Tests and measurements-Part 23-3: Screening and filtering tests-Test 23c: Shielding effectiveness of connectors and accessories-Line injection method

$50.44 $100.88 -50%
Product Code: IEC 60512-23-3
Stock In Stock
Edition: 2.0
Published: 12/2018
Number of Pages: 34
File Size: 1 file, 886 Bytes

Available Options

Product Description

Connectors for electrical and electronic equipment – Tests and measurements – Part 23-3: Screening and filtering tests – Test 23c: Shielding effectiveness of connectors and accessories – Line injection method

Introduction: This document is part of the IEC 60512 series within the group of standards identified as Part 23: Screening and filtering tests. It covers a method to measure the shielding (screening) effectiveness of shielded connectors or of shielding accessories for connectors that are non-inherently shielded, e.g. connector shielded housings and/or connector EMC cable glands, by measurement of the surface transfer impedance ZT (Ω) as a function of the frequency. By using a formula, ZT is then converted in shielding effectiveness SE (dB). In Part 23 there is another document, IEC 60512-23-7, Connectors for electronic equipment – Tests and measurements – Part 23-7 – Screening and filtering tests – Test 23g: Effective transfer impedance of connectors, that provides test 23g. The first difference between the method described in this document and test 23g is that here in test 23c, in the measurement of the transfer impedance ZT the capacitive coupling phenomena covered by the capacity coupling impedance ZF are considered negligible, while test 23g includes these effects to measure the effective surface transfer impedance ZTE. This test 23c is applicable to a wide range of applications: it covers circular connectors, rectangular connectors and connectors for PCBs, as well as connector shielding accessories, i.e. those accessories such as connector shielded housings and/or metal shielding plates, providing shielding properties to a non-inherently shielded connector. Test 23g is a variant of th

Scope: This part of IEC 60512 defines a standard test method for measuring the shielding effectiveness SE of a shielded connector, or of a connector not provided with integral shield once fitted with a shielding accessory and terminated with a screened cable. The complete assembly has a continuous 360° shielding capability throughout its length. NOTE 1 Practically, continuous 360° shielding is not always achievable based on the geometry of the connector. NOTE 2 Shielding” is used in this document with the same meaning as “screening”. This test method can be applied to shielded connectors and to connector accessories with shielding capability. The following different connector designs can be tested: circular connectors; rectangular connectors; connectors for printed boards; connector shielding accessories. NOTE 3 For the definition of “accessory” see IEV 581-24-10. A shielding accessory i.e. an accessory that confers shielding to a non-inherently shielded connector, may be a suitable set of shielded housings providing electrical continuity, along the mated connector set, between the screen of the (screened) cable at the cable outlet of the free cable connector housing and the metallic mounting surface for the fixed connector housing. The free connector housing is provided with a cable screen clamp. This test method utilizes the principle that the intrinsic shielding property of the connector/ accessory/cable assembly is its surface transfer impedance ZT which can be expressed as the longitudinal voltage inside the shield, relative to the current flow on the outside shell. This test method is based on two impedance-matched circuits. See Figure 1 for the measurement principle. The connector specimen under test is integrated into the secondary circuit 02. The impedance-matched injection line of the primary circuit 01, which activates the electromagnetic field, runs parallel to the surface of the specimen under test. This test is also suitable for measuring the shielding effectiveness of a connector fitted with triaxial contacts terminated with shielded, twisted pair cables, as used in data bus systems. NOTE 4 This standard has been adopted by ASD-STAN (formerly known as AE

Contents:

  • FOREWORD
  • INTRODUCTION
  • Scope

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
IEC 60512-23-3-2018 PDF

IEC 60512-23-3-2018 PDF

$50.44 $100.88