IEC 61643-11-2025 PDF

IEC 61643-11-2025 PDF

Low-voltage surge protective devices-Part 11: Surge protective devices connected to AC low-voltage power systems-Requirements and test methods

$163.93 $327.86 -50%
Product Code: IEC 61643-11
Stock In Stock
Edition: 2.0
Published: 06/2025
Number of Pages: 86
File Size: 0 files

Available Options

Product Description

Low-voltage surge protective devices – Part 11: Surge protective devices connected to AC low-voltage power systems – Requirements and test methods

Introduction: It has been assumed in the drafting of this International Standard that the execution of its provisions is entrusted to appropriately qualified and experienced persons. This document recognizes the internationally accepted level of protection against hazards such as electrical, mechanical, thermal, fire and radiation of SPDs when operated as in normal use taking into account the manufacturer's instructions. It also covers abnormal situations that can be expected in practice. This document takes into account the requirements of IEC 60364 as far as possible so that there is compatibility with the wiring rules when the SPD is connected to the supply mains. However, national wiring rules might differ. If the intended applications of an SPD are covered by different parts of the IEC 61643-X1 series, all relevant parts are applied, as far as is reasonable. This document addresses safety and performance tests for surge protective devices (SPDs) for AC applications in conjunction with IEC 61643-01. This document addresses T1 SPD, T2 SPD and T3 SPD according to IEC 61643-01. IEC 61643-12 addresses the selection and application principles of SPDs.

Scope: This document, together with IEC 61643-01, is applicable to devices for surge protection against indirect and direct effects of lightning or other transient overvoltages. These devices are intended to be connected to AC power circuits and equipment rated up to 1 000 V RMS, the preferred frequencies taken into account in this document are 50/60 Hz. Other frequencies are not excluded. Performance and safety requirements, tests and ratings are specified in this document. These devices contain at least one nonlinear component and are intended to limit surge voltages and divert surge currents. The test requirements provided by this document are based on the assumption that the SPD is connected to an AC power circuit fed by a power source providing a linear voltage-current characteristic. When the SPD is to be connected to a different kind of source or to a different frequency, careful consideration is required. This mainly applies with regard to system and fault conditions to be expected in such a system (e.g. expected short circuit current, TOV-stresses). This document can apply for railway applications, when related product standards do not exist for that area or for certain applications. Based on a risk assessment it might not be necessary to apply all requirements of this document to SPDs designed for specific power applications only, e.g. circuits with a low power capability, circuits supplied by nonlinear sources, circuits with protective separation from the utility supply. NOTE 1 More information on risk assessment is provided in IEC Guide 116. NOTE 2 Other exclusions based on national regulations are possible.

Contents:

  • FOREWORD
  • INTRODUCTION
  • Scope
  • 4.100 Power system
  • 4.100.1 AC between 47 Hz and 63 Hz
  • 4.100.2 AC other than the range of 47 Hz to 63 Hz
  • 6.2.100 Markings which are required on the body, or permanently attached to the
  • 6.2.100.1 Markings which shall be visible after installation
  • 6.2.100.2 Markings which are not required to be visible after installation
  • 6.2.101 Information to be provided by the manufacturer
  • 6.2.102 Information which shall be provided by the manufacturer for type testing, as
  • 7.100 Frequency
  • 8.3.6.4 Dedicated overstress behaviour
  • 8.3.9.100 TOVs caused by faults or disturbances in the low voltage system
  • 8.3.9.101 TOVs caused by faults in the high (medium) voltage system
  • 8.6.100 Portable SPDs defined as pluggable equipment type A
  • 9.3.3.1 Test procedure
  • 9.3.5.2 Power source characteristics for the operating duty test
  • 9.3.5.2.1 General
  • 9.3.5.2.3 SPD's modes of protection with follow current according to Annex B of
  • 9.3.6.2 Thermal protection test
  • 9.3.6.2.2 Test settings

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
IEC 61643-11-2025 PDF

IEC 61643-11-2025 PDF

$163.93 $327.86