ISO 14126-2023 PDF

ISO 14126-2023 PDF

Fibre-reinforced plastic composites-Determination of compressive properties in the in-plane direction

$60.00 $120.00 -50%
Product Code: ISO 14126
Stock In Stock
Edition: 2.
Published: 10/2023
Number of Pages: 38
File Size: 1 file, 2 Bytes

Available Options

Product Description

Composites plastiques renforcés de fibres - Détermination des caractéristiques en compression dans le plan

Introduction: This document, originally published in 1999, was based on ISO 8515[1] with the scope extended from glass-fibre reinforcement to include all fibre-reinforced plastic composites, such as composites based on carbon and aramid fibres. Other source documents consulted included ASTM D 3410[2], SACMA SRM1[3], prEN 2850[4], CRAG 400[5], DIN 65380[6] and JIS K7076[7]. Several different types of anti- buckling fixtures/loading jigs, different materials and different specimen sizes are covered by these source documents, although all are parallel-sided coupons. New or modified geometry support jigs are still being developed, for example in JIS K7018[8]. This document harmonizes and rationalizes the current situation by: a) concentrating on the quality of the test by limiting the maximum bending strain allowable (i.e. 10 % between 10 % and 90 % of the maximum load, as recommended by ASTM), so that an axial- load case can be assumed; b) standardizing on two related specimen designs, one principally for aerospace type unidirectional pre-impregnated materials (i.e. Type A) and one for other materials/formats (i.e. Types B1/B2). The chosen specimen design can be used with different loading fixtures; c) defining acceptable failure criteria (e.g. avoiding within grip failures); d) including an equation for determining the specimen minimum thickness to avoid Euler buckling proposed by ASTM for harmonization purposes (taken from ASTM D 3410[2] in a modified form); e) allowing any design of suppor

Scope: 1.1 This document specifies methods for determining the compressive properties, in directions parallel to the plane of lamination, of fibre-reinforced plastic composites, based on thermosetting or thermoplastic matrices. The compressive properties are of interest for specifications and quality- control purposes. The test specimens are machined from a flat test plate, or from suitable finished or semi-finished products. 1.2 Two loading methods and two types of specimen are described. The loading methods are: — Method 1: provides shear loading of the specimen (gauge length unsupported) — Method 2: provides combined loading of the specimen (gauge length unsupported) NOTE For tabbed specimens loaded using method 2, load is transferred through a combination of end- loading and shear-loading through the tabs. The specimen designs are: — Type A specimen: rectangular cross-section, fixed thickness, end-tabbed (mainly for aerospace style preimpregnates (~ 0,125 mm ply thickness) — Type B specimen: rectangular cross-section, range of thicknesses, untabbed or end-tabbed, two specimen sizes are available (B1 and B2). The Type A specimen is used for unidirectionally or biaxially reinforced materials tested in the fibre direction, where the fibres are normally either aligned continuous or aligned long (>7,5 mm) discontinuous. The Type B1 and B2 specimens are used for multi-directional aligned; mat, fabric and other multi-directionally reinforced materials where the fibre structure is more complex and/or coarser. 1.3 This document gives criteria for checking that the combination of test method and specimen design result in valid failures. It is noted that alternative test method/specimen combinations will not necessarily give the same result. 1.4 The methods specify required dimensions for the specimen. Tests carried out on specimens of other dimensions, or on specimens that are prepared under different conditions, can produce results that are not comparable. Other factors, such as the speed of testing, the support fixture used and the conditioning of the specimens, can influence the results.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ISO 14126-2023 PDF

ISO 14126-2023 PDF

$60.00 $120.00