ASTM A370-26 PDF

ASTM A370-26 PDF

Standard Test Methods and Definitions for Mechanical Testing of Steel Products

$56.50 $113.00 -50%
Product Code: ASTM A370
Stock In Stock
Published: 2026
Number of Pages: 51

Available Options

Product Description

Significance and Use
 4.1  The primary use of these test methods is testing to determine the specified mechanical properties of steel, stainless steel, and related alloy products for the evaluation of conformance of such products to a material specification under the jurisdiction of ASTM Committee A01 and its subcommittees as designated by a purchaser in a purchase order or contract.
 4.1.1  These test methods may be and are used by other ASTM Committees and other standards writing bodies for the purpose of conformance testing.
 4.1.2  The material condition at the time of testing, sampling frequency, specimen location and orientation, reporting requirements, and other test parameters are contained in the pertinent material specification or in a general requirement specification for the particular product form.
 4.1.3  Some material specifications require the use of additional test methods not described herein; in such cases, the required test method is described in that material specification or by reference to another appropriate test method standard.
 4.2  These test methods are also suitable to be used for testing of steel, stainless steel and related alloy materials for other purposes, such as incoming material acceptance testing by the purchaser or evaluation of components after service exposure.
 4.2.1  As with any mechanical testing, deviations from either specification limits or expected as-manufactured properties can occur for valid reasons besides deficiency of the original as-fabricated product. These reasons include, but are not limited to: subsequent service degradation from environmental exposure (for example, temperature, corrosion); static or cyclic service stress effects, mechanically-induced damage, material inhomogeneity, anisotropic structure, natural aging of select alloys, further processing not included in the specification, sampling limitations, and measuring equipment calibration uncertainty. There is statistical variation in all aspects of mechanical testing and variations in test results from prior tests are expected. An understanding of possible reasons for deviation from specified or expected test values should be applied in interpretation of test results.
 Scope
 1.1  These test methods cover procedures and definitions for the mechanical testing of steels, stainless steels, and related alloys. The various mechanical tests herein described are used to determine properties required in the product specifications. Variations in testing methods are to be avoided, and standard methods of testing are to be followed to obtain reproducible and comparable results. In those cases in which the testing requirements for certain products are unique or at variance with these general procedures, the product specification testing requirements shall control.
 1.2  The following mechanical tests are described:
 Sections
                Tension
 7 to 14
                Bend
 15
                Hardness
 16
                     Brinell
 17
                     Rockwell
 18
                     Portable
 19
                Impact
 20 to 30
                Keywords
 32
 1.3  Annexes covering details peculiar to certain products are appended to these test methods as follows:
 Annex
      Bar Products
 Annex A1
      Tubular Products
 Annex A2
      Fasteners
 Annex A3
      Round Wire Products
 Annex A4
      Significance of Notched-Bar Impact Testing
 Annex A5
      Converting Percentage Elongation of Round Specimens to           Equivalents for Flat Specimens
 Annex A6
      Testing Multi-Wire Strand
 Annex A7
      Rounding of Test Data
 Annex A8
      Methods for Testing Steel Reinforcing Bars
 Annex A9
      Procedure for Use and Control of Heat-Cycle Simulation
 Annex A10
 1.4  The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
 1.5  When these test methods are referenced in a metric product specification, the yield and tensile values may be determined in inch-pound (ksi) units then converted into SI (MPa) units. The elongation determined in inch-pound gauge lengths of 2 in. or 8 in. may be reported in SI unit gauge lengths of 50 mm or 200 mm, respectively, as applicable. Conversely, when these test methods are referenced in an inch-pound product specification, the yield and tensile values may be determined in SI units then converted into inch-pound units. The elongation determined in SI unit gauge lengths of 50 mm or 200 mm may be reported in inch-pound gauge lengths of 2 in. or 8 in., respectively, as applicable.
 1.5.1  The specimen used to determine the original units must conform to the applicable tolerances of the original unit system given in the dimension table not that of the converted tolerance dimensions.
 Note 1:   This is due to the specimen SI dimensions and tolerances being hard conversions when this is not a dual standard. The user is directed to Test Methods A1058 if the tests are required in SI units.
 1.6  Attention is directed to ISO/IEC 17025 when there may be a need for information on criteria for evaluation of testing laboratories.
 1.7   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
 1.8   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM A370-26 PDF

ASTM A370-26 PDF

$56.50 $113.00