ASTM A691/A691M-19(2025) PDF

ASTM A691/A691M-19(2025) PDF

Standard Specification for Carbon and Alloy Steel Pipe, Electric-Fusion-Welded for High-Pressure Service at High Temperatures

$36.00 $72.00 -50%
Product Code: ASTM A691/A691M
Stock In Stock
Published: 2025
Number of Pages: 6

Available Options

Product Description

This specification covers carbon and alloy steel pipe, electric-fusion-welded with filler metal added, fabricated from pressure-vessel-quality plate of several analyses and strength levels and suitable for high-pressure service at high temperatures. Heat treatment may or may not be required to attain the desired mechanical properties. The pipes are classified according to steel grades and are designated in classes according to the type of heat treatment performed in the pipe manufacture, whether the weld is radiographically examined, and whether the pipe has been pressure tested. The steel welds shall be made either manually or automatically by an electric process involving the deposition of filler metal. The welded joints shall have positive reinforcement at the center of each side of the weld. The contour of this reinforcement shall be smooth, and the deposited metal shall be fused smoothly and uniformly into the plate surface. The joints shall undergo tension, bend and pressure tests. Unacceptable surface imperfections shall be removed by grinding or machining. The depression after grinding or machining shall be blended uniformly into the surrounding surface. Repair of weld and base metal defects shall be done by welding.
 Scope
 1.1  This specification 2 covers carbon and alloy steel pipe, electric-fusion-welded with filler metal added, fabricated from pressure-vessel-quality plate of several analyses and strength levels and suitable for high-pressure service at high temperatures. Heat treatment may or may not be required to attain the desired mechanical properties or to comply with applicable code requirements. Supplementary requirements are provided for use when additional testing or examination is desired.
 1.2  The specification nominally covers pipe 16 in. [400 mm] in outside diameter and larger with wall thicknesses up to 3 in. [75 mm] inclusive. Pipe having other dimensions may be furnished provided it complies with all other requirements of this specification.
 1.3  Several grades and classes of pipe are provided.
 1.3.1   Grade  designates the type of plate used as listed in Table 1 .
 1.3.2   Class  designates the type of heat treatment performed in the manufacture of the pipe, whether the weld is radiographically examined, and whether the pipe has been pressure tested as listed in 1.3.3 .
 1.3.3  Class designations are as follows ( Note 1 ):
 Class
 Heat Treatment on Pipe
 Radiography, see Section
 Pressure Test, see Section
 10
 none
 none
 none
 11
 none
 9
 none
 12
 none
 9
 8.3
 13
 none
 none
 8.3
 20
 stress relieved, see 5.3.1
 none
 none
 21
 stress relieved, see 5.3.1
 9
 none
 22
 stress relieved, see 5.3.1
 9
 8.3
 23
 stress relieved, see 5.3.1
 none
 8.3
 30
 normalized, see 5.3.2
 none
 none
 31
 normalized, see 5.3.2
 9
 none
 32
 normalized, see 5.3.2
 9
 8.3
 33
 normalized, see 5.3.2
 none
 8.3
 40
 normalized and tempered, see 5.3.3
 none
 none
 41
 normalized and tempered, see 5.3.3
 9
 none
 42
 normalized and tempered, see 5.3.3
 9
 8.3
 43
 normalized and tempered, see 5.3.3
 none
 8.3
 50
 quenched and tempered, see 5.3.4
 none
 none
 51
 quenched and tempered, see 5.3.4
 9
 none
 52
 quenched and tempered, see 5.3.4
 9
 8.3
 53
 quenched and tempered, see 5.3.4
 none
 8.3
 Note 1:   Selection of materials should be made with attention to temperature of service. For such guidance, Specification A20/A20M may be consulted.
 1.4  Optional requirements of a supplementary nature are provided, calling for additional tests and control of repair welding, when desired.
 1.5  The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order.
 1.6   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM A691/A691M-19(2025) PDF

ASTM A691/A691M-19(2025) PDF

$36.00 $72.00