ASTM A888-26 PDF

ASTM A888-26 PDF

Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications

$60.50 $121.00 -50%
Product Code: ASTM A888
Stock In Stock
Published: 2026
Number of Pages: 63

Available Options

Product Description

This specification covers hubless cast iron soil pipe and fittings for use in gravity flow applications. These pipe and fittings are intended for non-pressure applications, as the selection of the proper size for sanitary drain, waste, vent, and storm drain systems allows free air space for gravity drainage. The pipe and fittings shall be iron castings suitable for installation and service for sanitary, storm drain, waste, and vent piping applications. The pipe and fittings shall meet all applicable requirements and tests given in this specification. Tensile test and chemical test shall be made to conform to the requirements specified. The pipe and fittings shall be uniformly coated with a material suitable for the purpose that is adherent, not brittle, and without a tendency to scale.
 Scope
 1.1  This specification covers hubless cast iron soil pipe and fittings for use in gravity flow applications. It establishes standards covering material, manufacture, mechanical and chemical properties, dimensions, coating, test methods, inspection, certification, and product marking for hubless cast iron soil pipe and fittings. These pipe and fittings are intended for non-pressure applications, as the selection of the proper size for sanitary drain, waste, vent, and storm drain systems allows free air space for gravity drainage.
 1.2  The EDP/ASA numbers indicated in this section represent a Uniform Industry Code adopted by the American Supply Association (ASA). A group designation prefix, 022, is assigned to hubless products, followed by the four-digit identification assigned to individual items and a check digit. This system has been instituted to facilitate EDP control through distribution channels, and is to be used universally in ordering and specifying product items. Those items with no EDP numbers are either new, special, or transitory and will be assigned numbers on subsequent prints of this specification.
 1.3  This specification covers pipe and fittings of the following patterns and applies to any other patterns that conform with the dimensions found in Tables 1 and 2 and all other applicable requirements given in this specification.
 1.3.1   Lengths:
 Figures
 EDP/ASA Identification Numbers for Hubless Pipe
 Fig. 1
 10 ft (3.0 m) in sizes and 5 ft. (1.5 m) 1 1 / 2  , 2, 3, 4, 5, 6, 8, 10, 12, and 15 in.
 Fig. 1, Fig. 2
 Method of Specifying Fittings
 Fig. 3
 1.3.2   Fittings:  
 Quarter Bend
 Fig. 5
 Quarter Bend, Reducing
 Fig. 6
 Quarter Bend, with Side Opening
 Fig. 7
 Quarter Bend, with Heel Opening
 Fig. 8
 Quarter Bend, Tapped
 Fig. 9
 Quarter Bend, Double
 Fig. 10
 Quarter Bend, Long
 Fig. 11
 Short Sweep
 Fig. 12
 Long Sweep
 Fig. 13
 Long Sweep, Reducing
 Fig. 14
 Fifth Bend
 Fig. 15
 Sixth Bend
 Fig. 16
 Eighth Bend
 Fig. 17
 Eighth Bend, Long
 Fig. 18
 Sixteenth Bend
 Fig. 19
 Sanitary Tee
 Fig. 20
 Sanitary Tee with Side Opening
 Fig. 21
 Sanitary Tee with 2 in. Side Opening R or L/R and L
 Fig. 22
 Sanitary Tee, New Orleans Special with Side Opening
 Fig. 23
 Sanitary Tee with 45° Side Openings and New Orleans
 Fig. 24
 Sanitary Special Tee Tapped
 Fig. 25
 Sanitary Tapped Tee, Horizontal Twin
 Fig. 26
 Sanitary Tapped Tee, Double Vertical
 Fig. 27
 Y Branch
 Fig. 28
 Y Branch, Double
 Fig. 29
 Y Branch, Upright
 Fig. 30
 Upright Y Wide Center Florida Special
 Fig. 31
 Y Branch, Combination 1 / 8  Bend
 Fig. 32
 Y Branch, Combination 1 / 8  Bend Double
 Fig. 33
 Sanitary Cross
 Fig. 34
 Sanitary Cross with Side Opening
 Fig. 35
 Sanitary Cross, New Orleans, with Side Openings
 Fig. 36
 Sanitary Cross, New Orleans, with 45° Special and  Regular Side Openings
 Fig. 37
 Sanitary Cross, Tapped
 Fig. 38
 Test Tee
 Fig. 39
 Tapped Extension Piece
 Fig. 40
 Increaser-Reducer
 Fig. 41
 Increaser-Reducer, Short
 Fig. 42
 Tapped Adapter
 Fig. 43
 Blind Plug
 Fig. 44
 Iron Body Cleanout, Tapped
 Fig. 45
 P Trap
 Fig. 46
 P Trap, Long
 Fig. 47
 P Trap, Deep Seal
 Fig. 48
 P Trap, with Primer
 Fig. 49
 P Trap, with Tapped Inlet
 Fig. 50
 Tapped Inlet, Double
 Fig. 51
 Modified Combination Wye and 1 / 8   Bend, Double
 Fig. 52
 Modified Combination Wye and 1 / 8   Bend, Double, Extended
 Fig. 53
 Two-Way Cleanout
 Fig. 54
 Twin Cleanout
 Fig. 55
 Closet Bend, Regular and Reducing
 Fig. 56
 Closet Flange Riser
 Fig. 57
 Tapping Bosses
 Fig. 58
 Double Sweep Sanitary Tee (Extended)
 Fig. 59
 Running Trap with Double Vents
 Fig. 60
 P Trap with Tapped or Hubless Side Inlet
 Fig. 61
 Vented Tub Wye Extended, Double
 Fig. 62
 Vented Tub Wye Extended Offset, Left or Right
 Fig. 63
 Vented Tub Wye
 Fig. 64
 Double Two-Way Cleanout
 Fig. 65
 1.4  The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
 1.5  The committee with jurisdiction over this standard is aware of another comparable standard published by the Cast Iron Soil Pipe Institute, CISPI 301.
 Note 1:   The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
 1.6   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM A888-26 PDF

ASTM A888-26 PDF

$60.50 $121.00