ASTM B359/B359M-25E01 PDF

ASTM B359/B359M-25E01 PDF

Standard Specification for Copper and Copper-Alloy Seamless Condenser and Heat Exchanger Tubes With Integral Fins

$40.00 $80.00 -50%
Product Code: ASTM B359/B359M
Stock In Stock
Published: 2025
Number of Pages: 11

Available Options

Product Description

This specification establishes the requirements for seamless copper and copper alloy tubing on which the external or internal surface, or both, has been modified by a coldforming process to produce an integral enhanced surface for improved heat transfer. The tubes are typically used in surface condensers, evaporators, and heat exchangers. The seamless copper and copper alloy tubing shall have the internal or external surface, or both, modified by a cold forming process to produce an integral enhanced surface for improved heat transfer. The tube, after enhancing, shall be supplied in the annealed (O61) or as-fabricated temper. The enhanced sections of tubes in the as-fabricated temper are in the cold-worked condition produced by the fabricating operation. The unenhanced sections of tubes in the asfabricated temper are in the temper of the tube prior to enhancing, annealed (O61), or light drawn (H55), and suitable for rolling-in operations. Samples of annealed-temper (O61) tubes selected for test shall be subjected to microscopical examination and shall show uniform and complete recrystallation. Grain size and mechanical properties such as tensile strength and yield strength of the alloys shall be determined. Expansion and flattening tests shall be done to the alloys for performance evaluation. Non-destructive tests such as eddy-current test, hydrostatic test, and pneumatic test shall be done as well.
 Scope
 1.1  This specification 2 covers the requirements for seamless copper and copper alloy tubing on which the external or internal surface, or both, has been modified by a cold-forming process to produce an integral enhanced surface for improved heat transfer.
 1.2  The tubes are typically used in surface condensers, evaporators, and heat exchangers.
 1.3  The product shall be produced of the following coppers or copper alloys, as specified in the ordering information.
 Copper or Copper Alloy
 UNS No.
 Type of Metal
 C10100
 Oxygen-Free Electronic
 C10200
 Oxygen-Free without Residual Deoxidants
 C10300
 Oxygen-Free, Extra Low Phosphorus
 C10800
 Oxygen-Free, Low Phosphorus
 C12000
 DLP Phosphorized, Low Residual Phosphorus (See Note 1 )
 C12200
 DHP, Phosphorized, High Residual Phosphorus (See Note 1 )
 C14200
 DPA Phosphorized Arsenical (See Note 1 )
 C15630
 Nickel Phosphorus
 C19200
 Phosphorized, 1 % iron
 C23000
 Red Brass
 C44300
 Admiralty Metal Types B,
 C44400
 C, and
 C44550
 D
 C60800
 Aluminum Bronze
 C68700
 Aluminum Brass Type B
 C70400
 95-5 Copper-Nickel
 C70600
 90-10 Copper-Nickel
 C70620
 90-10 Copper-Nickel (Modified for Welding)
 C71000
 80-20 Copper-Nickel Type A
 C71500
 70-30 Copper-Nickel
 C71520
 70-30 Copper-Nickel (Modified for Welding)
 C72200
 Copper-Nickel
 Note 1:   Designations listed in Classification B224 .
 1.4   Units— The values stated in either in-pound units or SI units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems could result in nonconformance with the specification.
 1.5  Product produced in accordance with the Supplementary Requirements section for military applications shall be produced only to the inch-pound system of this specification.
 1.6  The following safety hazard caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Some specific hazards statements are given in Sections 1 , 12 and 18 .
 1.7  ( Warning— Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Use caution when handling mercury and mercury-containing products. See the applicable product Safety Data Sheet (SDS) for additional information. The potential exists that selling mercury or mercury-containing products, or both, is prohibited by local or national law. Users must determine legality of sales in their location.)
 1.8   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM B359/B359M-25E01 PDF

ASTM B359/B359M-25E01 PDF

$40.00 $80.00