ASTM C146-26 PDF

ASTM C146-26 PDF

Standard Test Methods for Chemical Analysis of Glass Sand

$40.00 $80.00 -50%
Product Code: ASTM C146
Stock In Stock
Published: 2026
Number of Pages: 13

Available Options

Product Description

Significance and Use
 3.1  These test methods can be used to ensure that the chemical composition of the glass sand meets the compositional specification required for this raw material.
 3.2  These test methods do not preclude the use of other methods that yield results within permissible variations. In any case, the analyst should verify the procedure and technique used by means of a National Institute of Standards and Technology (NIST) standard reference material or other similar material of known composition having a component comparable with that of the material under test. A list of standard reference materials is given in the NIST Special Publication 260 , current edition.
 Scope
 1.1  These test methods cover the chemical analysis of glass sands. They are useful for either high-silica sands (99 %+ silica (SiO 2 )) or for high-alumina sands containing as much as 12 % to 13 % alumina (Al 2 O 3 ). Generally nonclassical, these test methods are rapid and accurate. They include the determination of silica and of total R 2 O 3   (see 11.2.4 ), and the separate determination of total iron as iron oxide (Fe 2 O 3 ), titania (TiO 2 ), chromium oxide (Cr 2 O 3 ), zirconia (ZrO 2 ), and ignition loss. Included are procedures for the alkaline earths and alkalies. High-alumina sands may contain as much as 5 % to 6 % total alkalies and alkaline earths. It is recommended that the alkalies be determined by flame photometry and the alkaline earths by absorption spectrophotometry.
 1.2  These test methods, if followed in detail, will provide interlaboratory agreement of results.
 Note 1:   For additional information, see Test Methods C169 and Practices E50 .
 1.3  These test methods appear in the following order:
 Procedures for Referee Analysis:
 Section
  Silica (SiO 2 )—Double Dehydration
 10
  Total R 2 O 3 —Gravimetric
 11
  Fe 2 O 3 , TiO 2 , ZrO 2 , Cr 2 O 3 , by Photometric Methods and   Al 2 O 3 by Complexiometric Titration
 12 – 17
  Preparation of the Sample for Determination of Iron   Oxide, Titania, Alumina, and Zirconia
 12
  Iron Oxide (as Fe 2 O 3 ) by 1,10-Phenanthroline Method
 13
  Titania (TiO 2 ) by the Tiron Method
 14
  Alumina (Al 2 O 3 ) by the CDTA Titration Method
 15
  Zirconia (ZrO 2 ) by the Pyrocatechol Violet Method
 16
  Chromium Oxide (Cr 2 O 3 ) by the 1,5-Diphenylcarbo-   hydrazide Method
 17
 Procedures for Routine Analysis:
  Silica (SiO 2 )—Single Dehydration
 19
  Al 2 O 3 , CaO, and MgO—Atomic Absorption Spec-   trophotometry
 20 – 25
  Na 2 O and K 2 O—Flame Emission Spectrophotometry
 26 - 27
  Trace Chemical Species Analysis via ICP-OES and ICP-MS
 28
  Loss on Ignition (LOI)
 29
 1.4   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
 1.5   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM C146-26 PDF

ASTM C146-26 PDF

$40.00 $80.00