ASTM C25-24 PDF

ASTM C25-24 PDF

Standard Test Methods for Chemical Analysis of Limestone, Quicklime, and Hydrated Lime

$52.00 $104.00 -50%
Product Code: ASTM C25
Stock In Stock
Published: 2024
Number of Pages: 40

Available Options

Product Description

Significance and Use
 4.1  These test methods provide accurate and reliable analytical procedures to determine the chemical constituents of limestone, quicklime, and hydrated lime (see Note 1 ). The percentages of specific constituents which determine a material's quality or fitness for use are of significance depending upon the purpose or end use of the material. Results obtained may be used in relation to specification requirements.
 4.2  Because quicklime and hydrated lime quickly absorb water and carbon dioxide from the air, precision and bias are extremely dependent upon precautions taken during sample preparation and analysis to minimize excessive exposure to ambient conditions.
 Note 1:   These test methods can be applied to other calcareous materials if provisions are made to compensate for known interferences.
 Scope
 1.1  These test methods cover the chemical analysis of high-calcium and dolomitic limestone, quicklime, and hydrated lime. These test methods are classified as either standard (preferred) or alternative (optional).
 1.2  The standard test methods are those that employ classical gravimetric or volumetric analytical procedures and are typically those required for referee analyses where chemical specification requirements are an essential part of contractual agreement between buyer and seller.
 1.3  Alternative or optional test methods are provided for those who wish to use procedures shorter or more convenient than the standard methods for the routine determinations of certain constituents. Optional test methods may sometimes be preferred to the standard test methods, but frequently the use of modern and expensive instrumentation is indicated which may not be accessible to everyone. Therefore, the use of these test methods must be left to the discretion of each laboratory.
 1.4  The analytical procedures appear in the following order:
 Section
      Aluminum Oxide 
 15
      Available Lime Index 
 28
      Calcium and Magnesium Oxide:
       Alternative EDTA Titration Method 
 31
      Calcium Carbonate Equivalent 
 33
      Calcium Oxide:
       Gravimetric Method 
 16
       Volumetric Method 
 17
      Carbon Dioxide by Standard Method 
 22
      Combined Oxides of Iron and Aluminum 
 12
      Ferrous Iron 
 Appendix X5
      Free Calcium Oxide 
 Appendix X6
      Free Moisture in Hydrated Lime 
 21
      Free Moisture in Limestone 
 20
      Free Silica 
 29
      Insoluble Matter Including Silicon Dioxide:
       Standard Method 
   8
       Optional Perchloric Acid Method 
   9
      Insoluble Matter Other Than Silicon Dioxide 
 11
      Loss on Ignition 
 19
      Magnesium Oxide 
 18
      Manganese:
       Bismuthate Method 
 Appendix X4
       Periodate (Photometric) Method 
 27
      pH Determination of Alkaline Earth Solutions 
 34
      Phosphorus:
       Titrimetric Method 
 Appendix X3
       Molybdovanadate Method 
 26
      Silicon Dioxide 
 10
      Strontium Oxide 
 Appendix X2
      Sulfur Trioxide 
 23
      Total Carbon:
       Direct Combustion-Thermal Conductivity Cell       Method
 32
      Total Carbon and Sulfur:
       Combustion/Infrared Detection Method 
 35
      Total Iron:
       Standard Method, Potassium Dichromate       Titration 
 13
       Potassium Permanganate Titration Method 
 Appendix X1
       Ortho-Phenanthroline, Photometric Method 
 14
      Total Sulfur:
       Sodium Carbonate Fusion 
 24
       Combustion-Iodate Titration Method 
 25
       Unhydrated Oxides 
 30
 1.5   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
 For specific precautionary statements, see 9.3 , 10.2.1 , 18.4.3 , 31.6.4.2 , X2.3.1 , and X5.4.1.1 .
 1.6   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM C25-24 PDF

ASTM C25-24 PDF

$52.00 $104.00