ASTM D4851-07(2025) PDF

ASTM D4851-07(2025) PDF

Standard Test Methods for Coated and Laminated Fabrics for Architectural Use

$52.00 $104.00 -50%
Product Code: ASTM D4851
Stock In Stock
Published: 2025
Number of Pages: 21

Available Options

Product Description

Significance and Use
 5.1  The procedures in this standard can be used for acceptance testing of commercial shipments of coated and laminated fabrics for architectural use since these test methods have been used extensively in the trade for acceptance testing. Caution is advised, however, when testing adhesion of coating to fabric and breaking strength after crease fold because between laboratory precision is known to be poor (see 24.2 ). For these cases, comparative tests conducted, as directed in 5.1.1 , may be advisable.
 5.1.1  In cases of a dispute arising from differences in reported test results when using Test Methods D4851 for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens which are as homogeneous as possible and from a lot of material of the type in question. The test specimens should then be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using appropriate statistical analysis for unpaired data and an acceptable probability level chosen by the two parties before the testing is begun. If a bias is found, either its cause must be found and corrected or the purchaser and the supplier must agree to interpret future test results with consideration of the known bias.
 5.2  The uses and significance of specific properties are discussed in the appropriate sections of specific test methods.
 Scope
 1.1  These test methods cover the testing of coated and laminated fabrics made primarily for use in fabric roof systems. These coated and laminated fabrics are generally in either an air supported or tension supported construction of fabric roof systems.
 1.2  These methods can be used for most fiber-based, coated and laminated architectural fabrics.
 1.3  This standard includes the following sections that provide test procedures for coated and laminated architectural fabrics:
 Section
 Fabric Count
   8
 Mass per Unit Area
   9
 Fabric Thickness
 10
 Fabric Width
 11
 Fabric Length
 12
 Fabric Bow
 13
 Adhesion of Coating to Fabric
 14
 Uniaxial Elongation Under Static Load
 15
 Fabric Breaking Force
 16
 Breaking Strength After Crease Fold
 17
 Elongation at Break
 18
 Fabric Trapezoid Tear Force
 19
 Resistance to Accelerated Weathering
 20
 Solar Optical Properties
 21
 Fabric Flame Resistance
 22
 Noise Reduction Coefficient
 23
 1.4  These test methods include only testing procedures and do not include specifications or tolerances. They are intended as a guide for specifications. Any of these methods may be used in material specifications to evaluate requirements for a specific end use as related to a particular job.
 1.5  The values stated in either SI or inch-pound units are to regarded separately as the standard. Within the text, the inch-pound units are shown in parentheses. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other.
 1.6   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific warning statements are given in 14.1 , A1.3.3.1 , A2.3.3.1 , and A3.3.3.1 .
 1.7   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM D4851-07(2025) PDF

ASTM D4851-07(2025) PDF

$52.00 $104.00