ASTM D6750-23 PDF

ASTM D6750-23 PDF

Standard Test Methods for Evaluation of Engine Oils in a High-Speed, Single-Cylinder Diesel Engine—1K Procedure (0.4 % Fuel Sulfur) and 1N Procedure (0.04 % Fuel Sulfur)

$60.50 $121.00 -50%
Product Code: ASTM D6750
Stock In Stock
Published: 2023
Number of Pages: 70

Available Options

Product Description

Significance and Use
 5.1  These are accelerated engine oil tests (known as the 1K and 1N test procedures), performed in a standardized, calibrated, stationary single-cylinder diesel engine using either mass fraction 0.4 % sulfur fuel (1K test) or mass fraction 0.04 % sulfur fuel (1N test), that give a measure of ( 1 ) piston and ring groove deposit forming tendency, ( 2 ) piston, ring and liner scuffing and ( 3 ) oil consumption.
 5.2  The 1K test was correlated with vehicles equipped with certain multi-cylinder direct injection engines used in heavy duty and high speed service prior to 1989, particularly with respect to aluminum piston deposits, and oil consumption, when fuel sulfur was nominally mass fraction 0.4 %. These data are given in Research Report RR:D02-1273. 9
 5.3  The 1N test has been used to predict piston deposit formation in four-stroke cycle, direct injection, diesel engines that have been calibrated to meet 1994 U.S. federal exhaust emission requirements for heavy-duty engines operated on fuel containing less than mass fraction 0.05 % sulfur. See Research Report RR:D02-1321. 9
 5.4  These test methods are used in the establishment of diesel engine oil specification requirements as cited in Specification D4485 for appropriate API Performance Category oils (API 1509).
 5.5  These test methods are also used in diesel engine oil development.
 Scope
 1.1  These test methods cover the performance of engine oils intended for use in certain diesel engines. They are performed in a standardized high-speed, single-cylinder diesel engine by either the 1K (0.4 % mass fuel sulfur) or 1N (0.04 % mass fuel sulfur) procedure. 3 The only difference in the two test methods is the fuel used . Piston and ring groove deposit-forming tendency and oil consumption are measured. Also, the piston, the rings, and the liner are examined for distress and the rings for mobility. These test methods are required to evaluate oils intended to satisfy API service categories CF-4 and CH-4 for 1K, and CG-4 for 1N of Specification D4485 .
 1.2  These test methods, although based on the original Caterpillar 1K/1N procedures, 3 also embody TMC information letters issued before these test methods were first published. These test methods are subject to frequent change. Until the next revision of these test methods, TMC will update changes in these test methods by the issuance of information letters which shall be obtained from TMC (see Annex A1 – Annex A4 ).
 1.3  The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
 1.3.1   Exception— Where there is no direct SI equivalent such as screw threads, national pipe threads/diameters, tubing size, or single source equipment specified. Also Brake Specific Fuel Consumption is measured in kilograms per kilowatthour.
 1.4  The following is the Table of Contents:
 Section
 Introduction
 Scope
 1
 Referenced documents
 2
 Terminology
 3
 Summary of Test Methods
 4
 Significance and Use
 5
 Apparatus
 6
 General Laboratory Requirements
 6.1
 Test Engine
 6.2
 Test Engine Accessories and Parts
 6.3
 Reagents and Materials
 7
 Test Oil Sample Requirements
 8
 Preparation of Apparatus
 9
 Engine Inspection
 9.1
 Engine Pre-Test Lubrication System Flush
 9.2
 Engine Pre-Test Measurements and Inspections
 9.3
 Engine Assembly
 9.4
 Pressure Testing of Fuel System Assembly
 9.5
 Calibration of Engine Test Stand
 10
 General Requirements and Frequency of Calibration
 10.1
 Runs
 10.2
 Specified Test Parameters
 10.3
 Calibration Test Acceptance Criteria
 10.4
 Action on Rejection of Calibration Test
 10.5
 Test Numbering
 10.6
 Reference Oils
 10.7
 Severity Adjustments
 10.8
 Engine Operating Procedure
 11
 Engine Run-In
 11.1
 Cool-Down Procedure
 11.2
 Warm-Up Procedure
 11.3
 Operating Conditions and Oil Additions
 11.4
 Measurement of Oil Consumption
 11.5
 Sampling Used Oil
 11.6
 Shutdowns, Lost Time and Off Tolerance Conditions
 11.7
 Recording of Exhaust Temperature
 11.8
 Air-Fuel Ratio Measurement
 11.9
 Recording of Engine Conditions
 11.10
 Humidity Requirements/Calibration/Measurement
 11.11
 Inspections, Photographs and Measurements
 12
 Reference to Reporting Form
 12.1
 Pre-Test Measurements of Engine Parts
 12.2
 Post-Test Information
 12.3
 Oil Inspections
 12.4
 Report
 13
 General Directions
 13.1
 Electronic Transmission of Test Results (Optional)
 13.12
 Reporting Calibration Test Results
 13.13
 Precision and Bias
 14
 Keywords
 15
 ANNEXES
 ASTM Test Monitoring Center Organization
 Annex A1
 ASTM Test Monitoring Center: Calibration Procedures
 Annex A2
 ASTM Test Monitoring Center: Maintenance Activities
 Annex A3
 ASTM Test Monitoring Center: Related Information
 Annex A4
 Specifications for Test Engine and Engine Build
 Annex A5
 Intake Air System Details
 Annex A6
 Exhaust System Details
 Annex A7
 Cooling System Details
 Annex A8
 Oil System Modifications and Instrument Locations
 Annex A9
 Other Pressure and Temperature Measurement Locations
 Annex A10
 Oil Consumption Linear Regression Method
 Annex A11
 Test Fuel Specifications
 Annex A12
 Lubrication System, Flush Apparatus and Procedure
 Annex A13
 Engine Operating Conditions
 Annex A14
 Procedure for Rating Piston and Liner
 Annex A15
 Calculation of Percent Offset and Percent Deviation
 Annex A16
 1K/1N Test Reporting
 Annex A17
 Parts List by Part Number (P/N) and Warranty
 Annex A18
 Safety Precautions
 Annex A19
 APPENDIXES
 Humidity Data
 Appendix X1
 Statistical Equations for Mean and Standard Deviation
 Appendix X2
 Examples of Forms for Reporting
 Appendix X3
 Optional Recording of Oil Pass Limits
 Appendix X4
 1.5   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements appear throughout the text. Being engine tests, these test methods do have definite hazards that shall be met by safe practices (see Annex A19 on Safety Precautions).
 1.6   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM D6750-23 PDF

ASTM D6750-23 PDF

$60.50 $121.00