ASTM D7320-18E01 PDF

ASTM D7320-18E01 PDF

Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine

$56.50 $113.00 -50%
Product Code: ASTM D7320
Stock In Stock
Published: 2018
Number of Pages: 53

Available Options

Product Description

Significance and Use
 5.1  This test method was developed to evaluate automotive engine oils for protection against oil thickening and engine wear during moderately high-speed, high-temperature service.
 5.2  The increase in oil viscosity obtained in this test indicates the tendency of an oil to thicken because of oxidation. In automotive service, such thickening can cause oil pump starvation and resultant catastrophic engine failures.
 5.3  The deposit ratings for an oil indicate the tendency for the formation of deposits throughout the engine, including those that can cause sticking of the piston rings in their grooves. This can be involved in the loss of compression pressures in the engine.
 5.4  The camshaft and lifter wear values obtained in this test provide a measure of the anti-wear quality of an oil under conditions of high unit pressure mechanical contact.
 5.5  The test method was developed to correlate with oils of known good and poor protection against oil thickening and engine wear. Specially formulated oils that produce less than desirable results with unleaded fuels were also used during the development of this test.
 5.6  The Sequence IIIG engine oil test has replaced the Sequence IIIF test and can be used in specifications and classifications of engine lubricating oils, such as the following:
 5.6.1  Specification D4485 ,
 5.6.2  Military Specification MIL-PRF-2104, and
 5.6.3  SAE Classification J183.
 Scope
 1.1  This test method covers an engine test procedure for evaluating automotive engine oils for certain high-temperature performance characteristics, including oil thickening, varnish deposition, oil consumption, as well as engine wear. Such oils include both single viscosity grade and multiviscosity grade oils that are used in both spark-ignition, gasoline-fueled engines, as well as in diesel engines.
 1.1.1  Additionally, with nonmandatory supplemental requirements, a IIIGA Test (Mini Rotary Viscometer and Cold Cranking Simulator measurements), a IIIGVS Test (EOT viscosity increase measurement), or a IIIGB Test (phosphorous retention measurement) can be conducted. These supplemental test procedures are contained in Appendix X1 , Appendix X2 , and Appendix X3 , respectively.
 Note 1:   Companion test methods used to evaluate engine oil performance for specification requirements are discussed in SAE J304.
 1.2  The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
 1.2.1   Exception— Where there is no direct SI equivalent such as screw threads, national pipe threads/diameters, and tubing size.
 1.3  This test method is arranged as follows:
 Section
 Introduction
 Scope
 1
 Referenced Documents
 2
 Terminology
 3
 Summary of Test Methods
 4
 Significance and Use
 5
 Apparatus
 6
  Laboratory
 6.1
  Drawings
 6.2
  Specified Equipment
 6.3
  Test Engine
 6.4
   Engine Parts
 6.4.1
  Engine Speed and Load Control
 6.5
  Fluid Conditioning Module
 6.6
   Engine Cooling System
 6.6.1
  Flushing Tank
 6.7
  Coolant Mixing Tank
 6.8
  Condenser Cooling Systems
 6.9
  Engine Oil-Cooling System
 6.10
  Fuel System
 6.11
  Induction Air Supply Humidity, Temperature, and Pressure
 6.12
  Temperature Measurement
 6.13
   Thermocouple Location
 6.13.1
  Air-to-Fuel Ratio Determination
 6.14
   Injector Flow Testing
 6.14.1
  Exhaust and Exhaust Back Pressure Systems
 6.15
  Blowby Flow Rate Measurement
 6.16
  Pressure Measurement and Pressure Sensor Location
 6.17
 Reagents and Materials
 7
  Test Fuel
 7.1
  Engine and Condenser Coolant
 7.2
  Coolant Additive
 7.3
  Coolant Preparation
 7.4
  Pre-Test Cleaning Materials
 7.5
  Sealing and Anti-seize Compounds
 7.6
 Test Oil Sample Requirements
 8
 Preparation of Apparatus
 9
  Condenser Cleaning
 9.1
  Intake Manifold Cleaning
 9.2
  Cleaning of Engine Parts (other than the block and heads)
 9.3
  Connecting Rod Cleaning
 9.4
  Engine Block Cleaning
 9.5
  Cylinder Head Cleaning
 9.6
  Engine Build-up Procedure
 9.7
   General Information
 9.7.1
   Special Parts
 9.7.2
   Hardware Information
 9.7.3
   Fastener Torque Specifications and Torquing Procedures
 9.7.4
    Main Bearing Cap Bolts
 9.7.4.1
    Cylinder Head Bolts
 9.7.4.2
    Torques for Miscellaneous Bolts, Studs, and Nuts
 9.7.4.3
  Parts Replacement
 9.8
  Engine Block Preparation
 9.9
  Piston Fitting and Numbering
 9.10
   Piston Ring Fitting
 9.10.1
  Pre-Test Camshaft and Lifter Measurements
 9.11
  Camshaft Bearing Installation
 9.12
  Camshaft Installation
 9.13
  Main Bearings
 9.14
   Crankshaft Installation
 9.14.1
   Main Bearing Cap Installation
 9.14.2
  Crankshaft Sprocket
 9.15
  Camshaft Sprocket, and Timing Chain
 9.16
  Crankshaft End Play
 9.17
  Piston Pin Installation
 9.18
   Piston Installation
 9.18.1
  Harmonic Balancer
 9.19
  Connecting Rod Bearings
 9.20
  Engine Front Cover
 9.21
  Coolant Inlet Adapter
 9.22
  Oil Dipstick Hole
 9.23
  Oil Pan
 9.24
  Cylinder Head Assembly
 9.25
  Adjustment of Valve Spring Loads
 9.26
  Cylinder Head Installation
 9.27
  Hydraulic Valve Lifters
 9.28
  Pushrods
 9.29
  Valve Train Loading
 9.30
  Intake Manifold
 9.31
  Rocker Covers
 9.32
  Water Inlet Adapter
 9.33
  Condenser
 9.34
  Coolant Outlet Adapter
 9.35
  External Oil Cooling System
 9.36
  Oil Sample Valve
 9.37
  Ignition System
 9.38
  Throttle Body
 9.39
  Accessory Drive Units
 9.40
  Exhaust Manifolds, Water-Cooled
 9.41
  Engine Flywheel
 9.42
  Pressure Checking of Engine Coolant System
 9.43
  Lifting of Assembled Engines
 9.44
  Mounting the Engine on the Test Stand
 9.45
  External Cooling System Cleaning
 9.46
  Engine Coolant Jacket Cleaning (Flushing)
 9.47
  Coolant Charging
 9.48
  Test Oil Charging
 9.49
  Engine Oil Pump Priming
 9.50
 Calibration
 10
  Laboratory and Engine Test Stand Calibration
 10.1
  Testing of Reference Oils
 10.2
  Reference Oil Test Frequency
 10.3
  Evaluation of Reference Oil Test Results
 10.4
  Status of Non-Reference Oil Tests Relative to Reference   Oil Test
 10.5
  Status of Test Stands Used for Non-Standard Tests
 10.6
  Data Acquisition and Control
 10.7
   Sample Rate
 10.7.1
   Measurement Accuracy
 10.7.2
   Temperature
 10.7.3
   Pressure
 10.7.4
   Flow
 10.7.5
   Speed
 10.7.6
   Load
 10.7.7
   Measurement Resolution
 10.7.8
   System Time Response
 10.7.9
   Quality Index
 10.7.10
 Engine Operating Procedure
 11
  Dipstick and Hole Plug
 11.1
  Dipstick Hole O-ring
 11.2
  Engine Start-up and Shutdown Procedures
 11.3
  Start-up
 11.4
  Scheduled Shutdown
 11.5
  Non-Scheduled Shutdowns
 11.6
  Oil Sampling
 11.7
  Oil Leveling
 11.8
  Air-to-Fuel-Ratio Measurement and Control
 11.9
  Air-to-Fuel Ratio Verification
 11.10
  Blowby Flow Rate Measurement
 11.11
  NOx Determinations
 11.12
  Data Recording
 11.13
  Initial run (10 min)
 11.14
  Engine Oil Quality Testing (100 h)
 11.15
  Test Termination
 11.16
 Determination of Test Results
 12
  Engine Disassembly
 12.2
  Preparation of Parts for Rating of Sticking, Deposits,   and Plugging
 12.3
  Piston Deposit Rating
 12.4
  Post-Test Camshaft and Lifter Wear Measurements
 12.5
  Viscosity Test
 12.6
  Testing Oil Samples for Wear Metals
 12.7
  Blowby Flow Rate Measurements
 12.8
  Oil Consumption Computation
 12.9
  Photographs of Test Parts
 12.10
  Retention of Representative Test Parts
 12.11
  Severity Adjustments
 12.12
  Determination of Operational Validity
 12.13
 Report
 13
  Report Forms
 13.1
  Precision of Reported Units
 13.4
 Precision and Bias
 14
 Keywords
 15
 ASTM Test Monitoring Center: Organization
 Annex A1
 ASTM Test Monitoring Center: Calibration Procedures
 Annex A2
 ASTM Test Monitoring Center: Maintenance Activities
 Annex A3
 ASTM Test Monitoring Center: Related Information
 Annex A4
 Sequence IIIG Test Parts Replacement Guidelines
 Annex A5
 Sequence IIIG Determination Volume of Engine Oil in Pan
 Annex A6
 Sequence IIIG Test Fuel Analysis
 Annex A7
 Sequence IIIG Test Report Forms and Data Dictionary
 Annex A8
 Sequence IIIG Test Air-to-Fuel Ratio Control Flow Chart
 Annex A9
 Sequence IIIG Test Set Points and Control States
 Annex A10
 Sequence IIIG Quality Index Upper and Lower Values
 Annex A11
 Sequence IIIG Engine Oil Level Worksheet
 Annex A12
 Blowby Flow Rate Determination
 Annex A13
 Safety Hazards
 Annex A14
 Sequence IIIG Blueprint Listing
 Annex A15
 Fluid Condition Module Components
 Annex A16
 Engine Build Worksheets
 Annex A17
 Engine Oil Cooling System Schematic
 Annex A18
 Guidelines For Hardware Subject To First-In/First-Out Criteria
 Annex A19
 Sequence IIIGA Test Procedure
 Appendix X1
 Sequence IIIGVIS Test Procedure
 Appendix X2
 Sequence IIIGB Test Procedure
 Appendix X3
 1.4   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific warning statements are provided in 6.14.1.1 and 7.1 .
 1.5   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM D7320-18E01 PDF

ASTM D7320-18E01 PDF

$56.50 $113.00