ASTM D7621-16(2021) PDF

ASTM D7621-16(2021) PDF

Standard Test Method for Determination of Hydrogen Sulfide in Fuel Oils by Rapid Liquid Phase Extraction

$40.00 $80.00 -50%
Product Code: ASTM D7621
Stock In Stock
Published: 2021
Number of Pages: 11

Available Options

Product Description

Significance and Use
 5.1  Excessive levels of hydrogen sulfide in the vapor phase above residual fuel oils in storage tanks can result in health hazards, violation of local occupational health and safety regulations, and public complaint. An additional concern is corrosion that can be caused by the presence of H 2 S during refining or other activities. Control measures to maintain safe levels of H 2 S require a precise method for the measurement of potentially hazardous levels of H 2 S in fuel oils. ( Warning— Safety. Hydrogen sulfide (H 2 S) is a very dangerous, toxic, explosive and flammable, colorless and transparent gas which can be found in crude oil and can be formed during the manufacture of the fuel at the refinery and can be released during handling, storage, and distribution. At very low concentrations, the gas has the characteristic smell of rotten eggs. However, at higher concentrations, it causes a loss of smell, headaches, and dizziness, and at very high concentrations, it causes instantaneous death. It is strongly recommended that personnel involved in the testing for hydrogen sulfide are aware of the hazards of vapor-phase H 2 S and have in place appropriate processes and procedures to manage the risk of exposure.)
 5.2  This test method was developed so refiners, fuel terminal operators, and independent testing laboratory personnel can rapidly and precisely measure the amount of H 2 S in residual fuel oils and distillate blend stocks, with a minimum of training, in a wide range of locations.
 5.3  Test Method D5705 provides a simple and consistent field test method for the rapid determination of H 2 S in the residual fuel oils vapor phase. However it does not necessarily simulate the vapor phase H 2 S concentration of a fuel storage tank nor does it provide any indication of the liquid phase H 2 S concentration.
 5.4  Test Method D6021 does measure the H 2 S concentration of H 2 S in the liquid phase, however it requires a laboratory and a skilled operator to perform the complex procedure and calculations, and does not offer any reproducibility data. This test method ( D7621 ) offers a 15 min automated test, simplicity, full precision, and a degree of portability.
 5.5  H 2 S concentrations in the liquid and vapor phase attempt to reach equilibrium in a static system. However, this equilibrium and the related liquid and vapor concentrations can vary greatly depending on temperature and the chemical composition of the liquid phase. The equilibrium of the vapor phase is disrupted the moment a vent or access point is opened to collect a sample.
 Scope
 1.1  This test method covers procedures (A and B) for the determination of the hydrogen sulfide (H 2 S) content of fuel oils such as marine residual fuels and blend stocks, with viscosity up to 3000 mm 2 s -1 at 50 °C, and marine distillate fuels, as measured in the liquid phase.
 Note 1:   Specification fuels falling within the scope of this test method are: ASTM Specification D396 , MIL-DTL-16884, and ISO 8217.
 1.2  Procedure A has been shown to eliminate interferences such as thiols (mercaptans) and alkyl sulfides. Procedure B can give elevated results if such interferences are present (see Annex A2 ).
 Note 2:   A procedure for measuring the amount of hydrogen sulfide in crude oil can be found in Appendix X1 . Full precision for Appendix X1 has not yet been determined.
 1.3  Valid ranges for the precision are given in Table 2 and Table 3. Measurements can be made outside these ranges however precision has not been determined.
 1.4  Samples containing FAME do not affect the measurement of hydrogen sulfide by this test method.
 1.5  The values stated in SI units are to be regarded as standard. Non-SI units given in parentheses are for information only.
 1.6   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
 1.7   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM D7621-16(2021) PDF

ASTM D7621-16(2021) PDF

$40.00 $80.00