ASTM D8279-25 PDF

ASTM D8279-25 PDF

Standard Test Method for Determination of Timing-Chain Wear in a Turbocharged, Direct-Injection, Spark-Ignition, Four-Cylinder Engine

$60.50 $121.00 -50%
Product Code: ASTM D8279
Stock In Stock
Published: 2025
Number of Pages: 64

Available Options

Product Description

Significance and Use
 5.1  This test method evaluates an automotive engine oil's lubricating efficiency in inhibiting timing-chain lengthening under operating conditions selected to accelerate timing-chain wear. Varying quality reference oils of known wear performance were used in developing the operating conditions of the test procedure.
 5.2  The test method can be used to screen lubricants for satisfactory lubrication of an engine timing chain and has application in gasoline, automotive, engine-oil specifications. It is expected to be used in specifications and classifications of engine lubricating oils, such as the following:
 5.2.1  ILSAC GF-6.
 5.2.2  Specification D4485 .
 5.2.3  SAE Classification J183.
 Scope
 1.1  Undesirable timing-chain wear has been observed with gasoline, turbocharged, direct-injection (GTDI) engines in field service, and data from correlating laboratory engine tests have shown that chain wear can be affected by appropriately formulated engine lubricating. A laboratory engine test has been developed to provide a means for screening lubricating oils for that specific purpose. The laboratory engine test is 216 h in length, conducted under varying conditions, and the increase in timing-chain length determined at the end of test is the primary result. This test method is commonly known as the Sequence X, Chain Wear (CW) Test.
 1.2  The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.
 1.2.1   Exception— Where there is no direct SI equivalent such as screw threads, national pipe threads/diameters, tubing size, or specified single source equipment.
 1.3   Table of Contents:  
 Section
 Scope
 1
 Referenced Documents
 2
 Terminology
 3
 Summary of Test Method
 4
 Significance and Use
 5
 Apparatus
 6
  Test Engine
 6.1
 Reagents and Materials
 7
 Preparation of Apparatus
 8
  Timing-chain Preparation, Installation, and Measurement
 8.20
  Test Stand Installation
 8.21
  Electronic Throttle Controller
 8.21.17
  Temperature Measurement
 8.23
  Pressure Measurement
 8.24
  Flowrate Measurement
 8.25
  Blowby Flowrate
 8.26
 Stand Calibration
 9
 Test Procedure
 10
  Pre-Test Procedure and Engine Break-In
 10.1
  Engine Start-up Procedures
 10.2
  Test Sequence
 10.3
  Engine Shutdown Procedures
 10.4
  Blowby Flowrate Measurement
 10.5
  Parameter Logging
 10.6
  Oil Consumption Calculation
 10.7
  General Maintenance
 10.8
  Special Maintenance Procedures
 10.9
  Blowby Flowrate Adjustment
 10.10
 Diagnostic Data Review
 11
 Test Results
 12
 Report
 13
 Precision and Bias
 14
 Keywords
 15
 ANNEXES
 ASTM TMC Organization
 Annex A1
 ASTM TMC: Calibration Procedures
 Annex A2
 ASTM TMC: Maintenance Activities
 Annex A3
 ASTM TMC: Related Information
 Annex A4
 Engine and Stand Parts
 Annex A5
 Safety Precautions
 Annex A6
 Engine Rebuild Templates
 Annex A7
 Engine Build Records
 Annex A8
 Cylinder Head Build
 A8.1
 Cylinder Bore Measurement
 A8.2
 Bearing Journal Measurements
 A8.3
 Engine Part Photographs, Schematics and Figures
 Annex A9
 Control and Data Acquisition Requirements
 Annex A10
 Dipstick Oil Level to Charge Conversions
 Annex A11
 Sequence X Report Forms and Data Acquisition
 Annex A12
 APPENDIXES
 Sources of Materials and Information
 Appendix X1
 Suggested Designs for Engine Fixing Brackets
 Appendix X2
 1.4   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
 1.5   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM D8279-25 PDF

ASTM D8279-25 PDF

$60.50 $121.00