ASTM E1806-23 PDF

ASTM E1806-23 PDF

Standard Practice for Sampling Steel and Iron for Determination of Chemical Composition

$52.00 $104.00 -50%
Product Code: ASTM E1806
Stock In Stock
Published: 2023
Number of Pages: 22

Available Options

Product Description

Significance and Use
 4.1  This practice covers all aspects of sampling and preparing steel and iron for chemical analysis as defined in Test Methods, Practices, and Definitions A751 and Specification A48/A48M . Such subjects as sampling location and the sampling of lots are defined.
 4.2  This practice includes most requirements for sampling steel and iron for analysis. Standard test methods that reference this practice need contain only special modifications and exceptions.
 4.3  All who use these procedures should be trained samplers capable of performing common sampling operations skillfully and safely. Only proper sampling equipment should be used.
 Scope
 1.1  This practice covers the sampling of all grades of steel, both cast and wrought, and all types (grades) of cast irons and blast furnace iron for chemical and spectrochemical determination of composition. This practice is similar to ISO 14284.
 1.2  This practice is divided into the following sections.
 Sections
 Requirements for Sampling and Sample Preparation
 6
 General
 6.1
 Sample
 6.2
 Selection of a Sample
 6.3
 Preparation of a Sample
 6.4
 Liquid Iron for Steelmaking and Pig Iron Production
 7
 General
 7.1
 Spoon Sampling
 7.2
 Probe Sampling
 7.3
 Preparation of a Sample for Analysis
 7.4
 Liquid Iron for Cast Iron Production
 8
 General
 8.1
 Spoon Sampling
 8.2
 Probe Sampling
 8.3
 Preparation of a Sample for Analysis
 8.4
 Sampling and Sample Preparation for the Determination of
 8.5
  Oxygen and Hydrogen
 Liquid Steel for Steel Production
 9
 General
 9.1
 Probe Sampling
 9.2
 Spoon Sampling
 9.3
 Preparation of a Sample for Analysis
 9.4
 Sampling and Sample Preparation for the Determination
 9.5
  of Oxygen
 Sampling and Sample Preparation for the Determination
 9.6
  of Hydrogen
 Pig Irons
 10
 General
 10.1
 Increment Sampling
 10.2
 Preparation of a Sample for Analysis
 10.3
 Cast Iron Products
 11
 General
 11.1
 Sampling and Sample Preparation
 11.2
 Sections
 Steel Products
 12
 General
 12.1
 Selection of a Laboratory Sample or a Sample for
 12.2
  Analysis from a Cast Product
 Selection of a Laboratory Sample or a Sample for
 12.3
  Analysis from a Wrought Product
 Preparation of a Sample for Analysis
 12.4
 Sampling of Leaded Steel
 12.5
 Sampling and Sample Preparation for the Determination
 12.6
  of Oxygen
 Sampling and Sample Preparation for the Determination
 12.7
  of Hydrogen
 Keywords
 13
 Annexes
 Sampling Probes for Use with Liquid Iron and Steel
 Annex A1
 Sampling Probes for Use with Liquid Steel for the
 Annex A2
  Determination of Hydrogen
 1.3  The values stated in SI units are regarded as standard. No other units of measurement are included in this standard.
 1.4   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific statements, see 6.4.3.5 , 9.4.4.3 , 12.5.1 , and Section 5 .
 1.5   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM E1806-23 PDF

ASTM E1806-23 PDF

$52.00 $104.00