ASTM E2266-22 PDF

ASTM E2266-22 PDF

Standard Guide for Design and Construction of Low-Rise Frame Building Wall Systems to Resist Water Intrusion

$52.00 $104.00 -50%
Product Code: ASTM E2266
Stock In Stock
Published: 2022
Number of Pages: 40

Available Options

Product Description

Significance and Use
 5.1  This guide may be used by public agencies to set standards affecting the weather resistance, durability, and performance of new building wall systems, exterior deck and stair components, doors, windows, penetrations and sealant joints beyond those specifically defined in the building codes.
 5.2  This guide may be used by building field inspectors as a resource for construction inspection during the construction phase of a project.
 5.3  This guide may be used by private organizations or individuals to set standards affecting the weather resistance, durability, and performance of building walls.
 5.4  This guide may be used by architects and engineers as a resource for making design decisions involving material selection, building wall detailing and specifications.
 5.5  This guide may be used by architects and engineers as a resource for conducting submittal review and construction observation during the construction administration phase of a project.
 5.6  This guide may be used by contractors as a resource and checklist for exercising field quality control.
 Scope
 1.1  This guide describes design, specification, selection, installation, and inspection of new building wall systems, exterior deck and stair components, doors, windows, penetrations and sealant joints of wood and metal frame buildings, typically four stories or less, to minimize water intrusion.
 1.2  This guide does not address prevention of damage caused by water originating from the use of wet building materials or from indoor or outdoor humidity. Water from these sources can be important, and the potential for damage caused by water from these sources must not be overlooked in building design or construction.
 1.3  This guide does not address roofing systems, except when the surface of a deck also serves as a roof and at locations where roof systems interface with building walls.
 1.4  This guide does not address any type of barrier wall system.
 1.5  This guide does not address any exterior insulation and finish system (EIFS).
 1.6  This guide does not address foundation conditions where the bottom of a slab on grade or the grade of a crawl space is at or below the water table or subject to hydrostatic pressure.
 1.7  This guide is intended to supplement and not duplicate building code requirements.
 1.8  Maintenance, although important, is not covered in detail.
 1.9  Application of finishes, such as paint and sealers, may be important in the performance of some types of cladding; however, this is not covered in detail.
 1.10  This guide applies only to constructions with sheathing, which facilitates installation of the water-resistive barrier and associated flashings in a common plane.
 1.11  The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.
 1.12   This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory requirements prior to use.
 1.13   Organization of Document:  
 Section
 Scope
 1
 Referenced Documents
 2
 Terminology
 3
 Summary of Guide
 4
 Significance and Use
 5
 General Design Principles
 6
 Design Practices
 7
 General Guidelines
 8
 Drainage Walls
 9
  Drainage Walls—General
 9.1
  Drainage Wall Cladding—Portland Cement Plaster (Stucco)
 9.2
  Drainage Wall Cladding—Wood and Wood-Derived Products
 9.3
  Drainage Wall Cladding—Vinyl Siding
 9.4
  Drainage Wall Cladding—Fiber-Cement Siding
 9.5
 Cavity Drainage Walls
 10
  Cavity Drainage Walls—General
 10.1
  Cavity Drainage Wall Cladding—Masonry
 10.2
 Wood Framed Decks and Stairs with Exposed Framing and Decking
 11
 Plaza Decks or Stairs with Enclosed Framing and a Waterproofing Membrane with Separate Wearing Surfaces
 12
 Plaza Decks or Stairs with Enclosed Framing and a Waterproofing Membrane with an Integral Wearing Surface
 13
 Windows, Doors, and Similar Wall Penetrations
 14
 Special Wall Configuration
 15
 Exterior Sealant Joints
 16
 Keywords
 17
 Appendix—Introduction to Guide Details
 Appendix X1
 Appendix—General Notes for Cement Plaster (Stucco) Details
 Appendix X2
 Appendix—Additional Resources
 Appendix X3
 1.14   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM E2266-22 PDF

ASTM E2266-22 PDF

$52.00 $104.00