ASTM B122/B122M-26 PDF

ASTM B122/B122M-26 PDF

Standard Specification for Copper-Nickel-Tin Alloy, Copper-Nickel-Zinc Alloy (Nickel Silver), and Copper-Nickel Alloy Plate, Sheet, Strip, and Rolled Bar

$43.00 $86.00 -50%
Product Code: ASTM B122/B122M
Stock In Stock
Published: 2026
Number of Pages: 6

Available Options

Product Description

This specification establishes the requirements for copper-nickel-tin, copper-nickel-zinc, and copper-nickel alloy plates, sheets, strips, and rolled bars made from UNS C70600, C70620, C71000, C71500, C71520, C72200, C72500, C73500, C74000, C74500, C75200, C76200, or C77000 alloy. Each product should be manufactured by hot or cold working, and annealed if required, to produce a uniform wrought structure that meets the specified temper properties. This specification also contains information on the standard tempers for and tensile strengths of hot-rolled, cold-rolled, and annealed tempers. In case of disagreements, the chemical composition is determined following appropriate methods listed here. Grain size is the standard requirement for all products in the annealed tempers.
 Scope
 1.1  This specification establishes the requirements for copper-nickel-tin alloy, copper-nickel-zinc alloy (nickel silver), and copper-nickel alloy plate, sheet, strip, and rolled bar. The following alloys are covered:
 Nominal Composition, %
 Copper Alloy
 Chro-
 UNS No.
 Copper
 Nickel
 Zinc
 Tin
 mium
 C70600
 90
 10
 ...
 ...
 ...
 C70620
 90
 10
 ...
 ...
 ...
 C71000
 80
 20
 ...
 ...
 ...
 C71500
 70
 30
 ...
 ...
 ...
 C71520
 70
 30
 ...
 ...
 ...
 C72200
 85
 15
 ...
 ...
 0.5
 C72500
 89
  9
 ...
 2
 ...
 C73500
 72
 18
 10
 ...
 ...
 C74000
 70
 10
 20
 ...
 ...
 C74500
 65
 10
 25
 ...
 ...
 C75200
 65
 18
 17
 ...
 ...
 C76200
 59
 12
 29
 ...
 ...
 C77000
 55
 18
 27
 ...
 ...
 Note 1:   Plates of copper-nickel alloy copper alloy UNS Nos. C70600, C70620, C71500, C71520, and C72200 for use as tube plates in surface condensers and heat exchangers are covered by Specification B171/B171M .
 1.2   Units— The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.
 1.3   The following safety hazard caveat pertains only to the test method(s) described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
 1.4   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM B122/B122M-26 PDF

ASTM B122/B122M-26 PDF

$43.00 $86.00