ASTM B395/B395M-18 PDF

ASTM B395/B395M-18 PDF

Standard Specification for U-Bend Seamless Copper and Copper Alloy Heat Exchanger and Condenser Tubes

$40.00 $80.00 -50%
Product Code: ASTM B395/B395M
Stock In Stock
Published: 2018
Number of Pages: 12

Available Options

Product Description

Significance and Use
 18.1  For purpose of determining compliance with the specified limits for requirements of the properties listed in the following table, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29 .       Property
 Rounded Unit for Observed or Calculated Value
   Chemical composition
    nearest unit in the last
      right-hand significant      digit used in expressing      the limiting value
   Tensile strength
    nearest ksi [nearest 5 MPa]
   Elongation
    nearest 1 %
   Expansion
    nearest 1 %
   Grain size
    nearest multiple of 0.005 mm
 Abstract
 This specification establishes the requirements for condenser, evaporator, and heat exchanger U-bends that are manufactured from seamless copper and copper alloy tube. The material of manufacture shall be of such quality and purity that the finished product shall have the properties and characteristics specified. The material shall conform to the chemical composition requirements specified. Tensile test, expansion test, flattening test, mercurous nitrate test or ammonia vapor test, nondestructive examination, hydrostatic test, and pneumatic test shall be made to conform to the requirements specified.
 Scope
 1.1  This specification 2 establishes the requirements for condenser, evaporator, and heat exchanger U-bend tubes that are manufactured from seamless copper and copper alloy tube.
 1.2   Units— The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
 1.3  This specification is applicable to product 2 in. [50 mm] or less, inclusive, in diameter.
 1.4  The product shall be produced from one of the following coppers or copper alloys, as specified in the ordering information:
 Copper or Copper Alloy UNS No.
 Previously Used Designation
 Type of Metal
 C10200
 OF A
 oxygen-free without residual deoxidants
 C10300
 ...
 oxygen-free, extra low phosphorus
 C10800
 ...
 oxygen-free, low phosphorus
 C12000
 DLP A
 phosphorized, low residual phosphorus
 C12200
 DHP A
 phosphorized, high residual phosphorus
 C14200
 DPA A
 phosphorized, arsenical
 C19200
 ...
 phosphorized, 1 % iron
 C23000
 ...
 red brass
 C44300
 Type B
 admiralty metal
 C44400
 Type C
 admiralty metal
 C44500
 Type D
 admiralty metal
 C60800
 ...
 aluminum bronze
 C68700
 Type B
 aluminum brass
 C70400
 ...
 95-5 copper-nickel
 C70600
 ...
 90-10 copper-nickel
 C70620
 ...
 90-10 copper-nickel- (modified for welding)
 C71000
 ...
 80-20 copper-nickel
 C71500
 ...
 70-30 copper-nickel
 C71520
 ...
 70-30 copper-nickel- (modified for welding)
 C72200
 ...
 copper-nickel
 (A)   Designations listed in Classification B224 .
 1.5  The following safety hazard caveat pertains only to the test methods described in this specification.
 1.5.1   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. ( Warning— Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Safety Data Sheet (SDS) for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law.)
 1.6   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM B395/B395M-18 PDF

ASTM B395/B395M-18 PDF

$40.00 $80.00