ASTM B564-26 PDF

ASTM B564-26 PDF

Standard Specification for Nickel Alloy Forgings

$40.00 $80.00 -50%
Product Code: ASTM B564
Stock In Stock
Published: 2026
Number of Pages: 11

Available Options

Product Description

This specification covers nickel alloy forgings. These alloys are classified into different grades according to their chemical composition. A chemical analysis shall be employed on each alloy in order to determine its chemical composition. Grain size and mechanical properties like tensile strength, yield strength, and elongation shall be measured. A tension test and nondestructive ultrasonic test shall be done on each specimen.
 Scope
 1.1  This specification covers forgings of:
 Alloy Type
 UNS Number(s)
 Low-carbon Cr-Ni-Fe-N
 R20033
 Low-carbon Ni-Cr-Mo
 N06035, N06058, N06059, N06044
 Low-carbon Ni-Cr-Mo-Cu
 N06200
 Low-carbon Ni-Cr-Mo-W
 N06686
 Low-carbon Ni-Fe-Cr-Mo-Cu
 N08034
 Ni-Fe-Cr-Mo-N
 N08935
 Low-carbon Ni-Mo-Cr
 N10276, N06022, N10362
 Low-carbon Ni-Mo-Cr-Ta
 N06210
 Ni
 N02200
 Ni-Co-Cr-Si
 N12160
 Ni-Cr-Al
 N06699
 Ni-Cr-Co-Mo
 N06617
 Ni-Cr-Fe
 N06600, N06603, N06690
 Ni-Cr-Fe-Al
 N06025
 Ni-Cr-Fe-Si
 N06045
 Ni-Cr-Mo-Nb
 N06625
 Ni-Cr-Mo-Si
 N06219
 Ni-Cr-Mo-W
 N06110
 Ni-Cr-W-Mo
 N06230
 Ni-Cu
 N04400
 Ni-Fe-Cr
 N08120
 Ni-Fe-Cr-Mo-Cu
 N08825, N08827
 Ni-Fe-Cr-W
 N06674
 Ni-Mo
 N10665, N10675, N10629
 Ni-Mo-Cr-Fe
 N10242, N10624
 1.1.1  Nickel-iron-chromium alloy UNS N08120 is normally employed in service temperatures above 1100 °F (593 °C) where resistance to creep and rupture is required, and are annealed to develop controlled grain size for optimum properties in this temperature range.
 1.1.2  Nickel-iron-chromium-tungsten alloy UNS N06674 is normally employed in service temperatures above 1100 °F (593 °C) where resistance to creep and rupture is required, and is annealed to develop optimum properties in this temperature range.
 1.1.3  Nickel-chromium-molybdenum-columbium (UNS N06625) products are furnished in two grades of different heat-treated conditions:
 1.1.3.1   Grade 1 (Annealed)— Material is normally employed in service temperatures up to 1100 °F (593 °C).
 1.1.3.2   Grade 2 (Solution annealed)— Material is normally employed in service temperatures above 1100 °F (593 °C) where resistance to creep and rupture are required.
 Note 1:   Hot-working or reannealing may change properties significantly, depending on working history and temperatures.
 1.2  The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
 1.3   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.
 1.4   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM B564-26 PDF

ASTM B564-26 PDF

$40.00 $80.00