ASTM C67/C67M-26 PDF

ASTM C67/C67M-26 PDF

Standard Test Methods for Sampling and Testing Brick and Structural Clay Tile

$52.00 $104.00 -50%
Product Code: ASTM C67/C67M
Stock In Stock
Published: 2026
Number of Pages: 21

Available Options

Product Description

These test methods cover procedures for the sampling and testing of brick and structural clay tile. The tests include modulus of rupture, compressive strength, absorption, saturation coefficient, effect of freezing and thawing, efflorescence, initial rate or absorption, and determination of weight, size, warpage, length chanange, and void areas. For purposes of these tests, full-size bricks, tiles, or solid masonry units shall be used as test specimens. They shall be representative of the lot of units from which they are to be selected in respect of the range of colors, textures, and sizes and shall be free of or brushed to remove dirt, mud, mortar, or other foreign materials unassociated with the manufacturing process.
 Scope
 1.1  These test methods cover procedures for the sampling and testing of brick and structural clay tile. Although not necessarily applicable to all types of units, tests include modulus of rupture, compressive strength, absorption, saturation coefficient, effect of freezing and thawing, efflorescence, initial rate of absorption and determination of weight, size, warpage, length change, and void area. (Additional methods of test pertinent to ceramic glazes include imperviousness, chemical resistance, opacity, and resistance to crazing.
 1.2  The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
 Note 1:   The testing laboratory performing this test method should be evaluated in accordance with Practice C1093 .
 1.3  The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.
 1.4  These test methods include the following sections:
 Section Heading
 Section
 Scope
 1
 Referenced Documents
 2
 Terminology
 3
 Sampling
 4
 Specimen Preparation
 5
 Modulus of Rupture (Flexure Test)
 6
 Compressive Strength
 7
 Absorption
 8
 Freezing and Thawing
 9
 Initial Rate of Absorption (Suction) (Laboratory Test)
 10
 Efflorescence
 11
 Weight Per Unit Area
 12
 Measurement of Size
 13
 Measurement of Warpage
 14
 Measurement of Length Change
 15
 Initial Rate of Absorption (Suction) (Field Test)
 16
 Measurement of Void Area in Cored Units
 17
 Measurement of Void Area in Deep Frogged Units
 18
 Measurement of Out of Square
 19
 Measurement of Shell and Web Thickness
 20
 Breaking Load
 21
 Imperviousness Test (of Ceramic Glazes)
 22
 Chemical Resistance Test (of Ceramic Glazes)
 23
 Autoclaved Crazing Test (of Ceramic Glazes)
 24
 Opacity Test (of Ceramic Glazes)
 25
 Precision and Bias
 26
 Keywords
 27
 Safety Precautions for Autoclave Equipment and Operation
 Appendix X1
 1.5   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
 1.6   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM C67/C67M-26 PDF

ASTM C67/C67M-26 PDF

$52.00 $104.00