ASTM C758-18 PDF

ASTM C758-18 PDF

Standard Test Methods for Chemical, Mass Spectrometric, Spectrochemical, Nuclear, and Radiochemical Analysis of Nuclear-Grade Plutonium Metal

$36.00 $72.00 -50%
Product Code: ASTM C758
Stock In Stock
Published: 2018
Number of Pages: 9

Available Options

Product Description

Significance and Use
 4.1  These test methods are designed to show whether a given material meets the purchaser's specifications.
 4.1.1  An assay is performed to determine whether the material has the specified plutonium content.
 4.1.2  Determination of the isotopic content of the plutonium is made to establish whether the effective fissile content is in compliance with the purchaser's specifications.
 4.1.3  Impurity content is verified by a variety of methods to ensure that the maximum concentration limit of specified impurities is not exceeded. Determination of impurities is also required for calculation of the equivalent boron content (EBC).
 4.2   Fitness for Purpose of Safeguards and Nuclear Safety Applications— Methods intended for use in safeguards and nuclear safety applications shall meet the requirements specified by Guide C1068 for use in such applications.
 Scope
 1.1  These test methods cover procedures for the chemical, mass spectrometric, spectrochemical, nuclear, and radiochemical analysis of nuclear-grade plutonium metal to determine compliance with specifications.
 1.2  The analytical procedures appear in the following order:
 Sections
 Dissolution Procedure
 2
 Plutonium by Controlled-Potential Coulometry
 3
 Plutonium by Amperometric Titration with Iron (II)
 2
 Plutonium by Ceric Sulfate Titration Test Method
 3
 Plutonium by Diode Array Spectrophotometry
 3
 Uranium by Arsenazo I Spectrophotometric Test Method
 8 – 10
 Thorium by Thorin Spectrophotometric Test Method
 11 – 13
 Iron by 1,10-Phenanthroline Spectrophotometric Test Method
 14 – 16
 Iron by 2,2ʹ-Bipyridyl Spectrophotometric Test Method
 17 – 23
 Impurities by ICP-AES
 Chloride by the Thiocyanate Spectrophotometric Test Method
 24 – 26
 Fluoride by Distillation-Spectrophotometric Test Method
 27 – 28
 Nitrogen by Distillation-Nessler Reagent Spectrophotometric Test  Method
 29 – 30
 Carbon by the Direct Combustion-Thermal Conductivity Test  Method
 31 – 33
 Sulfur by Distillation-Spectrophotometric Test Method
 34 – 36
 Isotopic Composition by Mass Spectrometry
 37 and 38
 Plutonium-238 Isotopic Abundance by Alpha Spectrometry
 Americium-241 by Extraction and Gamma Counting
 39 – 41
 Americium-241 by Gamma Counting
 3
 Gamma-Emitting Fission Products, Uranium, and Thorium by  Gamma-Ray Spectroscopy
 42 – 49
 Rare Earths by Copper Spark Spectrochemical Test Method
 50 – 52
 Tungsten, Niobium (Columbium), and Tantalum by Spectro-  chemical Test Method
 53 – 55
 Sample Preparation for Spectrographic Analysis for Trace Impuri-  ties
 56 – 60
 1.3  The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
 1.4   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific safeguard and safety hazards statements, see Section 6 .
 1.5   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM C758-18 PDF

ASTM C758-18 PDF

$36.00 $72.00