ASTM C759-18 PDF

ASTM C759-18 PDF

Standard Test Methods for Chemical, Mass Spectrometric, Spectrochemical, Nuclear, and Radiochemical Analysis of Nuclear-Grade Plutonium Nitrate Solutions

$40.00 $80.00 -50%
Product Code: ASTM C759
Stock In Stock
Published: 2018
Number of Pages: 18

Available Options

Product Description

Significance and Use
 4.1  These test methods are designed to show whether a given material meets the purchaser's specifications.
 4.1.1  An assay is performed to determine whether the material has the specified plutonium content.
 4.1.2  Determination of the isotopic content of the plutonium in the plutonium-nitrate solution is made to establish whether the effective fissile content is in compliance with the purchaser's specifications.
 4.1.3  Impurity content is determined by a variety of methods to ensure that the maximum concentration limit of specified impurities is not exceeded. Determination of impurities is also required for calculation of the equivalent boron content (EBC).
 4.2   Fitness for Purpose of Safeguards and Nuclear Safety Applications— Methods intended for use in safeguards and nuclear safety applications shall meet the requirements specified by Guide C1068 for use in such applications.
 Scope
 1.1  These test methods cover procedures for the chemical, mass spectrometric, spectrochemical, nuclear, and radiochemical analysis of nuclear-grade plutonium nitrate solutions to determine compliance with specifications.
 1.2  The analytical procedures appear in the following order:
 Sections
 Plutonium by Controlled-Potential Coulometry
 2
 Plutonium by Amperometric Titration with Iron(II)
 2
 Plutonium by Diode Array Spectrophotometry
 Free Acid by Titration in an Oxalate Solution
 8 to 15
 Free Acid by Iodate Precipitation-Potentiometric Titration   Test Method
 16 to 22
 Uranium by Arsenazo I Spectrophotometric Test Method
 23 to 33
 Thorium by Thorin Spectrophotometric Test Method
 34 to 42
 Iron by 1,10-Phenanthroline Spectrophotometric Test Method
 43 to 50
 Impurities by ICP-AES
 Chloride by Thiocyanate Spectrophotometric Test Method
 51 to 58
 Fluoride by Distillation-Spectrophotometric Test Method
 59 to 66
 Sulfate by Barium Sulfate Turbidimetric Test Method
 67 to 74
 Isotopic Composition by Mass Spectrometry
 75 to 76
 Plutonium-238 Isotopic Abundance by Alpha Spectrometry
 Americium-241 by Extraction and Gamma Counting
 77 to 85
 Americium-241 by Gamma Counting
 86 to 94
 Gamma-Emitting Fission Products, Uranium, and Thorium by Gamma-Ray Spectroscopy
 94 to 102
 Rare Earths by Copper Spark Spectrochemical Test Method
 103 to 105
 Tungsten, Niobium (Columbium), and Tantalum by Spectro-  chemical Test Method
 106 to 114
 Sample Preparation for Spectrographic Analysis for General  Impurities
 115 to 118
 1.3  The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.
 1.4   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific safeguard and safety hazard statements, see Section 6 .
 1.5   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM C759-18 PDF

ASTM C759-18 PDF

$40.00 $80.00