ASTM D1037-12(2020) PDF

ASTM D1037-12(2020) PDF

Standard Test Methods for Evaluating Properties of Wood-Base Fiber and Particle Panel Materials

$52.00 $104.00 -50%
Product Code: ASTM D1037
Stock In Stock
Published: 2020
Number of Pages: 32

Available Options

Product Description

Significance and Use
 3.1  These test methods cover small-specimen tests for wood-base fiber and particle panel materials that are made to provide:
 3.2  Data for comparing the mechanical and physical properties of various materials,
 3.3  Data for determining the influence on the basic properties of such factors as raw material and processing variables, post-treatments of panels, and environmental influences, and
 3.4  Data for manufacturing control, product research and development, and specification acceptance.
 3.5  Not all the tests outlined in these test methods may be necessary to evaluate any particular panel for any specified use. In each instance, therefore, it will be necessary to determine which tests shall be made.
 Scope
 1.1   Part A—General Test Methods for Evaluating the Basic Properties of Wood-Base Fiber and Particle Panel Materials— These test methods cover the determination of the properties of wood-base fiber and particle panel materials that are produced as mat-formed panels such as particleboard, medium-density fiberboard, hardboard, and oriented strand board.
 Section
 Significance and Use
 3
 Apparatus
 4
 Test Specimens
 5
 Moisture Content and Conditioning Requirements
 6
 Accelerated Aging
 7
 Size, Physical Properties and Appearance of Panels
 8
 Static Bending
 9
 Tension Parallel to Surface
 10
 Tension Perpendicular to Surface
 11
 Compression Parallel to Surface
 12
 Fastener Holding Tests:
  Lateral Nail Resistance
 13
  Nail Withdrawal
 14
  Nail-Head Pull-Through
 15
  Direct Screw Withdrawal
 16
 Hardness
 17
 Hardness Modulus
 18
 Shear in the Plane of the Panel
 19
 Glue-Line Shear (Block Type)
 20
 Falling Ball Impact
 21
 Abrasion Resistance by the U.S. Navy Wear Tester
 22
 Moisture Tests:
  Water Absorption and Thickness Swelling
 23
  Linear Expansion with Change in Moisture Content
 24
 Cupping and Twisting
 25
 Interlaminar Shear
 26
 Edgewise Shear
 27
 Compression-Shear
 28
 1.2   Part B—Acceptance and Specification Test Methods for Hardboard— The methods for Part B provide test procedures for measuring the following properties of hardboard:
 Section
 Thickness
 32
 Modulus of Rupture
 33
 Tension Strength Parallel to Surface
 34
 Tension Strength Perpendicular to Surface
 35
 Water Absorption and Thickness Swelling
 36
 Moisture Content and Specific Gravity
 37
 1.3  There are accepted basic test procedures for various fundamental properties of materials that may be used without modification for evaluating certain properties of wood-based fiber and particle panel materials. These test methods are included elsewhere in the Annual Book of ASTM Standards . The pertinent ones are listed in Table 1 . A few of the test methods referenced are for construction where the wood-base materials often are used.
 1.4  The values stated in inch-pound units are to be regarded as the standard. The SI equivalents are approximate in many cases. 1 in. = 25.4 mm, 1 lbf = 4.45 N.
 1.5   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
 1.6   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM D1037-12(2020) PDF

ASTM D1037-12(2020) PDF

$52.00 $104.00