ASTM D2671-21 PDF

ASTM D2671-21 PDF

Standard Test Methods for Heat-Shrinkable Tubing for Electrical Use

$40.00 $80.00 -50%
Product Code: ASTM D2671
Stock In Stock
Published: 2021
Number of Pages: 18

Available Options

Product Description

Significance and Use
 4.1  These test methods include most of the important tests used to characterize heat-shrinkable tubing. They are intended primarily for, but not limited to, extruded heat-shrinkable tubing.
 4.2  It is acceptable to use variations in these test methods or alternate contemporary methods of measurement to determine the values for the properties in this standard provided such methods ensure quality levels and measurement accuracy equal to or better than those prescribed herein. It is the responsibility of the organizations using alternate test methods to be able to demonstrate this condition. In cases of dispute, the methods specified herein shall be used.
 Note 2:   Provision for alternate methods is necessary because of (1) the desire to simplify procedures for specific applications without altering the result, and (2) the desire to eliminate redundant testing and use data generated during manufacturing process control, including that generated under Statistical Process Control (SPC) conditions, using equipment and methods other than those specified herein. An example would be the use of laser micrometers or optical comparators to measure dimensions.
 Scope
 1.1  These test methods cover the testing of heat-shrinkable tubing used for electrical insulation. Materials used include poly(vinyl chloride), polyolefins, fluorocarbon polymers, silicone rubber, and other plastic or elastomeric compounds.
 1.2  These test methods appear in the following sections:
 Procedure
 Section(s)
 Test Method(s)
 Adhesive Peel Strength
 94 – 100
 Brittleness Temperature
 40
 D746
 Color
 55 and 56
 D1535
 Color Stability
 57 – 62
 D1535
 Conditioning
 7
 D618
 Copper Stability
 89
 Corrosion Testing
 85 – 91
 Dielectric Breakdown
 20 – 25
 D149
 Dimensions
 8 – 13
 D876
 Flammability
 68
 D8355 (Methods A, C, or D)
 Fluid Resistance
 63 – 67
 Fungus Resistance
 100 – 104
 Heat Resistance
 49 – 54
 Heat Shock
 26 – 30
 Low-temperature Properties
 36 – 43
 Restricted Shrinkage
 14 – 19
 Selection of Test Specimens
 6
 Secant Modulus
 77 – 80
 D882
 Storage Life
 31 – 35
 Specific Gravity
 69 and 70
 D792
 Stress Modulus
 81 – 84
 D412
 Tensile Strength and Ultimate Elongation
 44 – 48
 D412
 Thermal Endurance
 92 and 93
 Volume Resistivity
 71 – 74
 D257
 Water Absorption
 75 and 76
 D570
 Melting Point
 100 – 104
 D3418
 1.3  The values stated in inch-pound units are to be regarded as standard, except for temperature, which shall be expressed in degrees Celsius. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
 1.4   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 5 and for fire test safety caveats see Test Methods D8355 .
 Note 1:   These test methods are similar, but not identical to, those in IEC 60684-2 (see also Note 9 ).
 1.5   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM D2671-21 PDF

ASTM D2671-21 PDF

$40.00 $80.00