ASTM D3032-21a PDF

ASTM D3032-21a PDF

Standard Test Methods for Hookup Wire Insulation

$52.00 $104.00 -50%
Product Code: ASTM D3032
Stock In Stock
Published: 2021
Number of Pages: 39

Available Options

Product Description

These test methods detail the standard procedures for testing hookup wire insulations including all components of the insulation system used on single insulated conductors or an assembly of single insulated conductors such as a cable bundle and harness or flat ribbon cable. The insulating materials include not only the primary insulation over the conductor, but also insulating jackets over shielded constructions. The test procedures covered here shall be performed in the conditions or shall determine the properties, as follows: axial stability (longitudinal change) after thermal exposure; bondability to potting compounds; capacitance; cold bend test; concentricity; crush resistance; dielectric breakdown voltage; dimensions; dry-arc tracking; dynamic cut-through; fluid immersion; high temperature shock; insulation-continuity proof tests; insulation resistance; partial discharge (corona) inception and extinction voltage; relative thermal life and temperature index; strip force; surface resistance; tensile properties; vertical flame test; voltage rating of hook-up wire; voltage withstand test; and wet arc-tracking.
 Scope
 1.1  These test methods cover procedures for testing hookup wire.
 1.2  For the purposes of these test methods, hookup wire insulation includes all components of the insulation system used on single insulated conductors or an assembly of single insulated conductors such as a cable bundle and harness or flat ribbon cable. The insulating materials include not only the primary insulation over the conductor, but also insulating jackets over shielded constructions.
 1.3  These test methods and their locations are as follows:
 Section
 Axial Stability (Longitudinal Change) After Thermal Exposure
 20
 Bondability of Insulation to Potting Compounds
 18
 Capacitance
 9 to 11
 Cold Bend Test
 25
 Concentricity
 25
 Crush Resistance
 19
 Dielectric Breakdown Voltage
 5
 Dimensions
 14
 Dry-arc Tracking
 28
 Dynamic Cut-through
 21
 Fluid Immersion
 22
 High Temperature Shock
 23
 Insulation-Continuity Proof Tests
 12
 Insulation Resistance
 6
 Partial Discharge (Corona) Inception and Extinction Voltage
 24
 Relative Thermal Life and Temperature Index
 13
 Strip Force
 26
 Surface Resistance
 26
 Tensile Properties
 16
 Vertical Flame
 17
 Vertical Flame Test A
 18.5 (Test Method D8354 )
 Vertical Flame Test B
 17.6 – 17.11.4
 Voltage Rating of Hook-Up Wire
 Annex A1
 Voltage Withstand Test
 8
 Wet Arc-tracking
 27
 1.4  The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.
 1.5   This standard measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not, by itself, incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.
 1.6   Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.
 1.7   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 17.1.3 , 24.4 , and Note 18 .
 1.8   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM D3032-21a PDF

ASTM D3032-21a PDF

$52.00 $104.00