ASTM D3702-24 PDF

ASTM D3702-24 PDF

Standard Test Method for Wear Rate and Coefficient of Friction of Materials in Self-Lubricated Rubbing Contact Using a Thrust Washer Testing Machine

$36.00 $72.00 -50%
Product Code: ASTM D3702
Stock In Stock
Published: 2024
Number of Pages: 6

Available Options

Product Description

Significance and Use
 5.1  This test method is used to determine the equilibrium rate of wear and coefficient of friction of materials in rubbing contact under useful operating conditions, that is, combinations of pressure and velocity that fall below the PV (pressure × velocity) limit of the test material. The user of this test method should determine to his own satisfaction whether the results of this test procedure correlate with field performance or other bench test machines. If the test conditions are changed, the wear rates may change and the relative value of one material with respect to another may also change.
 5.2  Test conditions may be selected from Table 1 .
 (A)   For many applications a wear rate exceeding 1.0 × 10 − 5  in./h (2.5 × 10 − 7  m/h) is considered excessive. Typical wear rates for some commonly used materials at different PV levels are:
 Acetal homopolymer at PV 1 :
 5 × 10 − 6  in./h to 1 × 10 − 5  in./h (1.3 × 10 − 7  m/h to 2.5 × 10 − 7  m/h)
 Acetal homopolymer at PV 2 :
 1 × 10 − 5  in./h to 3 × 10 − 5  in./h (2.5 × 10 − 7  m/h to 7.5 × 10 − 7  m/h)
 22 % PTFE-filled acetal homopolymer at PV 2 :
 3 × 10 − 6  in./h to 6 × 10 − 6  in./h (7.5 × 10 − 8  m/h to 1.5 × 10 − 7  m/h)
 Polyamide (Type 6-6) at PV 2 :
 1 × 10 − 5  in./h to 5 × 10 − 5  in./h (2.5 × 10 − 7  m/h to 1.3 × 10 − 6  m/h)
 15 % graphite filled polyimide restin at PV 3 :
 1 × 10 − 5  in./h to 2 × 10 − 5  in./h (2.5 × 10 − 7  m/h to 5 × 10 − 7  m/h)
 5.3  The precision of wear measurement is relatively independent of test duration or amount of wear, but the precision of wear rate (calculation) improves with test duration and amount of wear. It is generally believed that useful wear rate precision requires the selection of a test duration sufficient to produce 0.1 mm (0.004 in.) of wear. Test durations will often be in the 50 h to 4000 h range.
 Scope
 1.1  This test method covers the determination of wear rate and coefficient of friction for self-lubricated materials in rubbing contact by a testing machine 2 that utilizes a thrust washer specimen configuration.
 Note 1:   This machine may also be used to measure coefficient of friction.
 1.2  The values in SI units are to be regarded as the standard. In cases where materials, products, or equipment are available only in inch-pound units, SI values in parentheses are for information only.
 1.3   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
 1.4   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM D3702-24 PDF

ASTM D3702-24 PDF

$36.00 $72.00