ASTM D4177-22E01 PDF

ASTM D4177-22E01 PDF

Standard Practice for Automatic Sampling of Petroleum and Petroleum Products

$56.50 $113.00 -50%
Product Code: ASTM D4177
Stock In Stock
Published: 2022
Number of Pages: 49

Available Options

Product Description

Significance and Use
 4.1  Representative samples of petroleum and petroleum products are required for the determination of chemical and physical properties, which are used to establish standard volumes, prices, and compliance with commercial terms and regulatory requirements. This practice does not cover sampling of electrical insulating oils and hydraulic fluids. This practice does not address how to sample crude at temperatures below the freezing point of water.
 PART I—General
 This part is applicable to all petroleum liquid sampling whether it be crude oil or refined products. Review this section before designing or installing any automatic sampling system.
 Scope
 1.1  This practice describes general procedures and equipment for automatically obtaining samples of liquid petroleum and petroleum products, crude oils, and intermediate products from the sample point into the primary container. This practice also provides additional specific information about sample container selection, preparation, and sample handling. If sampling is for the precise determination of volatility, use Practice D5842 (API MPMS Chapter 8.4) in conjunction with this practice. For sample mixing and handling, refer to Practice D5854 (API MPMS Chapter 8.3). This practice does not cover sampling of electrical insulating oils and hydraulic fluids.
 1.2   Table of Contents:  
 Section
 INTRODUCTION
 Scope
 1
 Referenced Documents
 2
 Terminology
 3
 Significance and Use
 4
 PART I–GENERAL
 Representative Sampling Components
 5
 Design Criteria
 6
 Automatic Sampling Systems
 7
 Sampling Location
 8
 Mixing of the Flowing Stream
 9
 Proportionality
 10
 Sample Extractor Grab Volume
 11
 Containers
 12
 Sample Handling and Mixing
 13
 Control Systems
 14
 Sample System Security
 15
 System Proving (Performance Acceptance Tests)
 16
 Performance Monitoring
 17
 PART II–CRUDE OIL
 Crude Oil
 18
 PART III–REFINED PRODUCTS
 Refined Products
 19
 KEYWORDS
 Keywords
 20
 ANNEXES
 Calculations of the Margin of Error based on Number of Sample Grabs
 Annex A1
 Theoretical Calculations for Selecting the Sampler Probe Location
 Annex A2
 Portable Sampling Units
 Annex A3
 Profile Performance Test
 Annex A4
 Sampler Acceptance Test Data
 Annex A5
 APPENDIXES
 Design Data Sheet for Automatic Sampling System
 Appendix X1
 Comparisons of Percent Sediment and Water versus Unloading Time Period
 Appendix X2
 Sampling Frequency and Sampling System Monitoring Spreadsheet
 Appendix X3
 Sampling System Monitoring—Additional Diagnostics
 Appendix X4
 1.3   Units— The values stated in either SI units or US Customary (USC) units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Except where there is no direct SI equivalent, such as for National Pipe Threads/diameters, or tubing.
 1.4   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
 1.5   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM D4177-22E01 PDF

ASTM D4177-22E01 PDF

$56.50 $113.00