ASTM D4565-20 PDF

ASTM D4565-20 PDF

Standard Test Methods for Physical and Environmental Performance Properties of Insulations and Jackets for Telecommunications Wire and Cable

$40.00 $80.00 -50%
Product Code: ASTM D4565
Stock In Stock
Published: 2020
Number of Pages: 19

Available Options

Product Description

Significance and Use
 5.1  Dimensional measurements, properly interpreted, provide information with regard to the conductors, insulation, or jacket. The dimensional measurements provide data for research and development, engineering design, quality control, and acceptance or rejection under specifications.
 Scope
 1.1  These test methods cover procedures for the physical testing of thermoplastic insulations and jackets used on telecommunications wire and cable and the testing of physical characteristics and environmental performance properties of completed products. To determine the procedure to be used on the particular insulation or jacket or on the completed wire or cable, make reference to the specification for that product.
 1.2  These test methods appear in the following sections of this standard:
 Test Method
 Section(s)
 Dimensional Measurements of Insulations, Jackets, Miscellaneous
 Cable Components, and of Completed Cable
 4 – 9
 Cross-sectional Areas
 9
 Diameters
 6
 Eccentricity
 8
 Thickness
 7
 Physical and Environmental Tests of Insulation and Jackets
 10 – 25
 Aging Test (Jackets Only)
 24
 Cold Bend (Insulation Only)
 16
 Environmental Stress Crack (Polyolefin Jackets Only)
 21
 Heat Distortion (Jackets Only)
 22
 Heat Shock (Jackets Only)
 23
 Insulation Adhesion
 19
 Insulation and Jacket Shrinkback (Oven Test)
 14
 Insulation Compression
 20
 Insulation Shrinkback (Solder Test)
 15
 Melt Flow Rate Change—Polyolefin Materials
 12
 Oil Immersion Test (Jackets Only)
 25
 Oxygen Induction Time (Polyolefin Insulation Only)
 17
 Oxygen Induction Time (Cable Filling Compound Only)
 18
 Tensile and Elongation Tests
 13
 Physical and Environmental Tests of Insulations and Jackets of
 Completed Wire and Cable
 26 – 42
 Cable Torsion Test
 38
 Compound Flow Test (Filled Core Wire and Cable Only)
 42
 Corrugation Extensibility Test
 36
 Cable Impact Test
 33
 Jacket Bonding Tests
 29
 Jacket Notch Test
 32
 Jacket Peel or Pull
 28
 Jacket Slip Strength Test
 30
 Procedure
 Section(s)
 Pressure Test (Air Core Wire and Cable Only)
 40
 Sheath Adherence Test
 31
 Water Penetration Test (Filled Core Wire and Cable Only)
 41
 Wire and Cable Bending Test
 34
 Wire breaking strength
 37
 1.3  The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard, except where only SI units are given.
 1.4   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statement see 19.1 .
 1.5   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM D4565-20 PDF

ASTM D4565-20 PDF

$40.00 $80.00