ASTM D5966-22 PDF

ASTM D5966-22 PDF

Standard Test Method for Evaluation of Engine Oils for Roller Follower Wear in Light-Duty Diesel Engine

$40.00 $80.00 -50%
Product Code: ASTM D5966
Stock In Stock
Published: 2022
Number of Pages: 19

Available Options

Product Description

Significance and Use
 5.1  This test method is used to determine the ability of an engine crankcase oil to control wear that can develop in the field under low to moderate engine speeds and heavy engine torques. Side-by-side comparisons of two or more oils in delivery van fleets were used to demonstrate the field performance of various oils. The specific operating conditions of this test method were developed to provide correlation with the field performance of these oils.
 5.2  This test method, along with other test methods, defines the minimum performance level of the Category API CG-4 for heavy duty diesel engine lubricants. Passing limits for this category are included in Specification D4485 .
 5.3  The design of the engine used in this test method is not representative of all modern diesel engines. Consider this factor, along with the specific operating conditions used to accelerate wear, when extrapolating test results.
 Scope
 1.1  This engine lubricant test method is commonly referred to as the Roller Follower Wear Test. Its primary result, roller follower shaft wear in the hydraulic valve lifter assembly, has been correlated with vehicles used in stop-and-go delivery service prior to 1993. It is one of the test methods required to evaluate lubricants intended to satisfy the API CG-4 performance category. This test has also been referred to as the 6.2 L Test.
 1.2  The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
 1.2.1   Exceptions— Where there is no direct SI equivalent, such as pipe fittings, thermocouple diameters, and NPT screw threads. Also, roller follower wear is measured in mils.
 1.3   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
 1.4   Table of Contents:
 Section
 Scope
 1
 Referenced Documents
 2
 Terminology
 3
 Summary of Test Method
 4
 Significance and Use
 5
 Reagents
 7
  Guidelines on Substitution
 7.1
 Apparatus
 6
 Preparation of Apparatus
 8
  New Engine Preparation
 8.1
  Installation of Auxiliary Systems and  Miscellaneous Components
 8.2
 Test Procedure
 9
  Description of Test Segments and Organization  of Test Procedure Sections
 9.1
  Engine Parts Replacement
 9.2
  Engine Starting Procedure
 9.3
  Normal Engine Shutdown Procedure
 9.4
  Emergency Shutdown Procedure
 9.5
  Unscheduled Shutdown and Downtime
 9.6
  New Engine Break-In
 9.7
  Pretest Procedure
 9.8
  Fifty-Hour Steady State Test
 9.9
  Periodic Measurements
 9.10
  Oil Sampling and Oil Addition Procedures
 9.11
  End of Test (EOT) Procedure
 9.12
 Calculation and Interpretation of Test Results
 10
  Environment of Parts Measurement Area
 10.1
  Roller Follower Shaft Wear Measurements
 10.2
  Oil Analysis
 10.3
  Assessment of Test Validity
 10.4
 Final Test Report
 11
  Reporting Calibration Test Results
 11.1
  Report Forms
 11.2
  Interim Non-Valid Calibration Test Summary
 11.3
  Severity Adjustments
 11.4
 Precision and Bias
 12
  Precision
 12.1
  Precision Estimate
 12.2
  Bias
 12.3
 Keywords
 13
 ANNEXES
 Guidelines for Test Part Substitution or Modification
 Annex A1
 Guidelines for Units and Specification Formats
 Annex A2
 Detailed Specifications of Apparatus
 Annex A3
 Calibration
 Annex A4
 Final Report Forms
 Annex A5
 Illustrations
 Annex A6
 Kinematic Viscosity at 100°C Procedure for the  Roller Follower Wear Test
 Annex A7
 Enhanced Thermal Gravimetric Analysis (TGA)  Procedure for Soot Measurement
 Annex A8
 Sources of Materials and Information
 Annex A9
 APPENDIXES
 PC-9 Reference Diesel Fuel Properties
 Appendix X1
 Diagnostic Data Review
 Appendix X2
 1.5   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM D5966-22 PDF

ASTM D5966-22 PDF

$40.00 $80.00