ASTM D5967-21 PDF

ASTM D5967-21 PDF

Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine

$52.00 $104.00 -50%
Product Code: ASTM D5967
Stock In Stock
Published: 2021
Number of Pages: 24

Available Options

Product Description

Significance and Use
 5.1  This test method was developed to evaluate the viscometric performance of engine oils in turbocharged and intercooled four-cycle diesel engines. Results are obtained from used oil analysis.
 5.2  The test method is used for engine oil specification acceptance when all details of the procedure are followed.
 Scope
 1.1  This test method covers an engine test procedure for evaluating diesel engine oils for performance characteristics, including viscosity increase and soot concentrations (loading). 2 This test method is commonly referred to as the Mack T-8.
 1.2  This test method also provides the procedure for running an extended length T-8 test, which is commonly referred to as the T-8E and an abbreviated length test, which is commonly referred to as T-8A. The procedures for the T-8E and the T-8A are identical to the T-8 with the exception of the items specifically listed in Annex A8 and Annex A9 respectively. Additionally, the procedure modifications listed in Annex A8 and Annex A9 refer to the corresponding section of the T-8 procedure.
 1.3  The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
 1.3.1   Exceptions— Where there is no direct SI equivalent such as the units for screw threads, National Pipe Threads/diameters, tubing size, sole source equipment suppliers, and oil consumption in grams per kilowatt-hour.
 1.4   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See Annex A6 for specific safety precautions.
 1.5  A Table of Contents follows:
 Scope
 1
 Referenced Documents
 2
 Terminology
 3
 Summary of Test Method
 4
 Significance and Use
 5
 Apparatus
 6
  General Description
 6.1
  The Test Engine
 6.2
  Mack Test Engine
 6.2.1
  Engine Cooling System
 6.2.2
  Engine Oil System
 6.2.3
  Auxiliary Oil System
 6.2.4
  Crankcase Aspiration
 6.2.5
  Blowby Meter
 6.2.6
  Air Supply and Filtration
 6.2.7
  Fuel Supply
 6.2.8
  Intake Manifold Temperature Control
 6.2.9
 Engine Fluids
 7
  Test Oil
 7.1
  Test Fuel
 7.2
  Engine Coolant
 7.3
  Cleaning Materials
 7.4
 Preparation of Apparatus at Rebuild
 8
  Cleaning of Parts
 8.1
  Valves, Seats, Guides, and Springs
 8.2
  Cylinder Liner, Piston, and Piston Ring Assembly
 8.3
  Injectors and Injection Pump
 8.4
  Assembly Instructions
 8.5
  Measurements
 8.6
 Laboratory and Engine Test Stand Calibration/Non-Reference Requirements
 9
  Calibration Frequency
 9.1
  Calibration Reference Oils
 9.2
  Test Numbering
 9.3
  New Laboratories and New Test Stands
 9.4
  Calibrated Laboratories and Test Stands
 9.5
  Calibration Test Acceptance
 9.6
  Failing Calibration Tests
 9.7
  Non-Reference Oil Test Requirements
 9.8
 Procedure
 10
  Pretest Procedure
 10.1
  Engine Start-Up
 10.2
  Engine Shutdown
 10.3
  Test Cycle
 10.4
  Oil Addition/Drain
 10.5
  Oil Samples
 10.6
  Oil Consumption Calculations
 10.7
  Fuel Samples
 10.8
  Periodic Measurements
 10.9
  Blowby
 10.10
  Centrifugal Oil Filter Mass Gain
 10.11
  Oil Filter Δ P Calculation
 10.12
  Post Test
 10.13
 Inspection of Fuel and Oil During Test
 11
  Oil Inspection
 11.1
  Fuel Inspections
 11.2
  Oil Consumption
 11.3
 Report
 12
  Reporting Test Results
 12.1
  Deviations from Test Operational Limits
 12.2
  Electronic Transmission of Test Results
 12.3
  Plots of Operational Data
 12.4
 Precision and Bias
 13
  Precision
 13.1
  Bias
 13.2
 Keywords
 14
 Annexes
 Report Forms
 Annex A1
 Sensor Locations
 Annex A2
 Kinematic Viscosity At 100 °C For Test Method D5967 Samples
 Annex A3
 Enhanced Thermal Gravimetric Analysis (TGA) Procedure
 Annex A4
 Procurement of Test Materials
 Annex A5
 Safety Precautions
 Annex A6
 Data Dictionary
 Annex A7
 T-8E Extended Length Test Requirements
 Annex A8
 T-8A Abbreviated Length Test Requirements
 Annex A9
 Mack T-8A, T-8, and T-8E Fuel Requirements
 Annex A10
 1.6   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM D5967-21 PDF

ASTM D5967-21 PDF

$52.00 $104.00