ASTM D6201-25 PDF

ASTM D6201-25 PDF

Standard Test Method for Dynamometer Evaluation of Unleaded Spark-Ignition Engine Fuel for Intake Valve Deposit Formation

$52.00 $104.00 -50%
Product Code: ASTM D6201
Stock In Stock
Published: 2025
Number of Pages: 27

Available Options

Product Description

Significance and Use
 5.1   Test Method— The Coordinating Research Council sponsored testing to develop this test method to evaluate a fuel's tendency to form intake valve deposits.
 5.1.1   State and Federal Legislative and Regulatory Action— Regulatory action by California Air Resources Board (CARB) 8 and the United States Environmental Protection Agency (EPA) 9 necessitate the acceptance of a standardized test method to evaluate the intake system deposit forming tendency of an automotive spark-ignition engine fuel.
 5.1.2   Relevance of Results— The operating conditions and design of the engine used in this test method are not representative of all engines. These factors shall be considered when interpreting test results.
 5.2   Test Validity:  
 5.2.1   Procedural Compliance— The test results are not considered valid unless the test is completed in compliance with all requirements of this test method. Deviations from the parameter limits presented in Sections 11 – 13 will result in an invalid test. Apply engineering judgment during conduct of the test method when assessing any anomalies to ensure validity of the test results.
 5.2.2   Engine Compliance— A test is not considered valid unless the test engine meets the quality control inspection requirements as described in Sections 9 and 11 .
 Scope
 1.1  This test method covers an engine dynamometer test procedure for evaluation of intake valve deposit formation of unleaded spark-ignition engine fuels. 2 This test method uses a Ford Ranger 2.3 L four-cylinder engine. This test method includes detailed information regarding the procedure, hardware, and operations.
 1.2  The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.
 1.3  This test method is arranged as follows:
 Subject
 Section
 Scope
 1
 Referenced Documents
 2
 Terminology
 3
 Summary of Test Method
 4
 Significance and Use
 5
 Apparatus
 6
  Laboratory Facilities
 6.1
  Engine and Cylinder Head Build-Up and Measurement Area
 6.1.1
  Engine Operating Area
 6.1.2
  Fuel Injector Testing Area
 6.1.3
  Intake Valve Rinsing and Parts Cleaning Area
 6.1.4
  Parts Rating and Intake Valve Weighing Area
 6.1.5
  Test Stand Laboratory Equipment
 6.2
  Test Stand Configuration
 6.2.1
  Dynamometer Speed and Load Control System
 6.2.2
  Intake Air Supply System
 6.2.3
  Exhaust System
 6.2.4
  Fuel Supply System
 6.2.5
  Engine Control Calibration
 6.2.6
  Ignition System
 6.2.7
  Engine Coolant System
 6.2.8
  External Oil System
 6.2.9
  Temperature Measurement Equipment and Locations
 6.2.10
  Pressure Measurement Equipment and Locations
 6.2.11
  Flow Measurement Equipment and Locations
 6.2.12
  Speed and Load Measurement Equipment and Locations
 6.2.13
  Exhaust Emissions Measurement Equipment and Location
 6.2.14
  DPFE (EGR) Voltage Measurement Equipment and Location
 6.2.15
  Ignition Timing Measurement Equipment and Location
 6.2.16
  Test Engine Hardware
 6.3
  Test Engine Parts
 6.3.1
  New Parts Required
 6.3.2
  Reusable Engine Parts
 6.3.3
  Special Measurement and Assembly Equipment
 6.4
 Reagents and Materials
 7
 Hazards
 8
 Preparation of Apparatus
 9
  Test Stand Preparation
 9.1
  Engine Block Preparation
 9.2
  Preparation of Miscellaneous Engine Components
 9.3
  Cylinder Head Preparation
 9.4
  Cylinder Head Assembly
 9.5
  Cylinder Head Installation
 9.6
  Final Engine Assembly
 9.7
 Calibration
 10
  Instrumentation Calibration
 10.1
 Procedure
 11
  Pretest Procedure
 11.1
  Engine Operating Procedure
 11.2
  Periodic Measurements and Functions
 11.3
  End of Test Procedures
 11.4
 Determination of Test Results
 12
  Post-Test Intake Valve Weighing Procedure
 12.1
  Photographs of Parts—General
 12.2
  Induction System Rating
 12.3
  Determination of Test Validity-Engine Conformance
 12.4
 Report
 13
 Precision and Bias
 14
 Keywords
 15
 Annexes
 Detailed Specifications and Photographs of Apparatus
 Annex A1
 Engine Part Number Listing
 Annex A2
 Statistical Equations for Mean and Standard Deviation
 Annex A3
 1.4   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific warning statements are given throughout this test method.
 1.5   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM D6201-25 PDF

ASTM D6201-25 PDF

$52.00 $104.00