ASTM D6593-18E01 PDF

ASTM D6593-18E01 PDF

Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation in a Spark-Ignition Internal Combustion Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions

$60.50 $121.00 -50%
Product Code: ASTM D6593
Stock In Stock
Published: 2018
Number of Pages: 79

Available Options

Product Description

Significance and Use
 5.1  This test method is used to evaluate an automotive engine oil's control of engine deposits under operating conditions deliberately selected to accelerate deposit formation. This test method was correlated with field service data, determined from side-by-side comparisons of two or more oils in police, taxi fleets, and delivery van services. The same field service oils were then used in developing the operating conditions of this test procedure.
 FIG. 1  Schematic of Engine Fuel System
 5.2  This test method, along with other test methods, defines the minimum performance level of the API Category SL (detailed information about this category is included in Specification D4485 ). This test method is also incorporated in automobile manufacturers' factory-fill specifications.
 5.3  The basic engine used in this test method is representative of many that are in modern automobiles. This factor, along with the accelerated operating conditions, should be considered when interpreting test results.
 Scope
 1.1  This test method covers and is commonly referred to as the Sequence VG test, 2 and it has been correlated with vehicles used in stop-and-go service prior to 1996, particularly with regard to sludge and varnish formation. 3 It is one of the test methods required to evaluate oils intended to satisfy the API SL performance category.
 1.2  The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.
 1.2.1   Exception— Where there is no direct SI equivalent such as screw threads, national pipe threads/diameters, tubing size, or specified single source equipment.
 1.3   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in 7.7 , 7.10.2.2 , 8.3.4.2 , 8.4.4.3 , 9.2.6 , 9.3.4.5 , 12.1.1.7 , 12.2.1.4 , and Annex A5 .
 1.4  A Table of Contents follows:
 Section
 Scope
 1
 Referenced Documents
 2
 Terminology
 3
 Summary of Test Method
 4
 Significance and Use
 5
 Apparatus (General Description)
 6
 Apparatus (The Test Engine)
 7
 Sequence VG Test Engine
 7.1
 Required New Engine Parts
 7.2
 Reusable Engine Parts
 7.3
 Specially Fabricated Engine Parts
 7.4
 Special Engine Measurement and Assembly Equipment
 7.5
 Miscellaneous Engine Components-Preparation
 7.6
 Solvents and Cleaners Required
 7.7
 Assembling the Test Engine-Preparations
 7.8
 Assembling the Test Engine-Installations
 7.9
 Engine Installation on the Test Stand
 7.10
 Engine Fluids (Supply/Discharge Systems)
 8
 Intake Air
 8.1
 Fuel and Fuel System
 8.2
 Engine Oil and Engine Oil System
 8.3
 Coolants
 8.4
 Measurement Instrumentation
 9
 Temperatures
 9.1
 Pressures
 9.2
 Flow Rates
 9.3
 Fuel Consumption
 9.4
 Speed and Load
 9.5
 Exhaust Gas
 9.6
 Humidity
 9.7
 Miscellaneous Laboratory Equipment
 10
 Test Stand Calibration
 11
 Test Procedure
 12
 Pre-Test Procedure
 12.1
 Engine Operating Procedure
 12.2
 Periodic Measurements and Functions
 12.3
 Special Maintenance Procedures
 12.4
 Diagnostic Data Review
 12.5
 End of Test Procedure
 12.6
 Interpretation of Test Results
 13
 Parts Rating Area-Environment
 13.1
 Sludge Ratings
 13.2
 Varnish Ratings
 13.3
 Clogging
 13.4
 Sticking
 13.5
 Used Oil Analyses
 13.6
 Assessment of Test Validity
 14
 General
 14.1
 Used Oil Analyses-Interpretation
 14.2
 Blowby Flow Rate
 14.3
 Manifold Absolute Pressure
 14.4
 Fuel Consumption Rate
 14.5
 Oil Consumption
 14.6
 Engine Parts Replacement
 14.7
 Quality Index and Deviation Percentage
 14.8
 Final Test Report
 15
 Report Forms
 15.1
 Precision and Bias
 16
 Keywords
 17
 ANNEXES
 ASTM Test Monitoring Center Organization
 Annex A1
 ASTM Test Monitoring Center: Calibration Procedures
 Annex A2
 ASTM Test Monitoring Center: Maintenance Activities
 Annex A3
 ASTM Test Monitoring Center: Related Information
 Annex A4
 Safety Precautions
 Annex A5
 Control and Data Acquisition Requirements
 Annex A6
 Detailed Specifications and Photographs of Apparatus
 Annex A7
 Special Service Tools for the Test Engine
 Annex A8
 Test Engine Part Number Listing
 Annex A9
 External Oil Heat Exchanger Cleaning Technique
 Annex A10
 Sequence VG Report Forms and Data Dictionary
 Annex A11
 Dipstick Calibration
 Annex A12
 Critical Part Supplier List
 Annex A13
 Operational Data Log-Engine Oil
 Annex A14
 Rating Worksheets
 Annex A15
 Fuel Injector Flow Measurements
 Annex A16
 APPENDIXES
 Piston and Ring Measurements Record Forms
 Appendix X1
 Sources of Materials and Information
 Appendix X2
 Description of Scott Quarterly Gas Audit Service
 Appendix X3
 1.5   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM D6593-18E01 PDF

ASTM D6593-18E01 PDF

$60.50 $121.00