ASTM D6618-23 PDF

ASTM D6618-23 PDF

Standard Test Method for Evaluation of Engine Oils in Diesel Four-Stroke Cycle Supercharged 1M-PC Single Cylinder Oil Test Engine

$56.50 $113.00 -50%
Product Code: ASTM D6618
Stock In Stock
Published: 2023
Number of Pages: 55

Available Options

Product Description

Significance and Use
 5.1  The test method is designed to relate to high-speed, supercharged diesel engine operation and, in particular, to the deposit control characteristics and antiwear properties of diesel crankcase lubricating oils.
 5.2  The test method is useful for the evaluation of diesel engine oil quality and crankcase oil specification acceptance. This test method, along with others, defines the minimum performance level of the API categories CF and CF-2 (detailed information about passing limits for these categories is included in Specification D4485 ). It is also used in MIL-PRF-2104.
 5.3  The results are significant only when all details of the procedure are followed. The basic engine used in this test method has a precombustion chamber (as compared to direct injection) and is most useful in predicting performance of engines similarly equipped. This factor should be considered when extrapolating test results. It has been found useful in predicting results with high sulfur fuels (that is, greater than 0.5 % by mass) and with certain preemission controlled engines. It has also been found useful when correlated with deposit control in two-stroke cycle diesel engines.
 Scope
 1.1  This test method covers a four-stroke cycle diesel engine test procedure for evaluating engine oils for certain high-temperature performance characteristics, particularly ring sticking, ring and cylinder wear, and accumulation of piston deposits. Such oils include both single viscosity SAE grade and multiviscosity SAE grade oils used in diesel engines. It is commonly known as the 1M-PC test (PC for Pre-Chamber) and is used in several API oil categories, notably the CF and CF-2 and the military category described in MIL-PRF-2104 (see Note 1 ).
 Note 1:   Companion test methods used to evaluate other engine oil performance characteristics for API oil categories CF and CF-2 are discussed in SAE J304. The companion tests used by the military can be found in MIL-PRF-2104.
 1.2  The values stated in SI units are to be regarded as standard.
 1.2.1   Exception— The values in parentheses are provided for information only.
 1.3   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
 1.4  This test method is arranged as follows:
 TABLE OF CONTENTS
 Scope
 1
 Reference Documents
 2
 Terminology
 3
 Summary of Test Method
 4
 Significance and Use
 5
 Apparatus
 6
 Test Engine
 6.1
 Engine Accessories
 6.2 – 6.14
 Engine Oil System
 6.15
 Cooling System
 6.16
 Fuel System
 6.17
 Intake Air System
 6.18
 Exhaust System
 6.19
 Blowby Meter
 6.20
 Thermocouples
 6.21
 Parts
 6.22
 Instrumentation
 6.23
 Crankcase Paint
 6.24
 Reagents and Materials
 7
 Fuel
 7.1
 Test Oil
 7.2
 Engine Coolant
 7.3
 Cleaning Materials
 7.4
 Safety
 8
 Preparation of Apparatus
 9
 Supplementary Service Information
 9.1
 General Engine Inspection
 9.2
 Intake Air System
 9.3
 Cooling System
 9.4
 Engine Cooling System Cleaning
 9.5
 Instrumentation Calibration Requirements
 9.6
 Engine Crankcase Cleaning
 9.7
 Additional Oil Filter
 9.8
 Flushing Procedure Components
 9.9
 Flushing Procedures
 9.10
 Piston Cleaning Preparation
 9.11
 Cylinder Head
 9.12
 Fuel Nozzle
 9.13
 Measurement
 9.14
 Procedure
 10
 Engine Break-in
 10.1
 Pre-Test Preparations
 10.2
 Warm-up Procedure
 10.3
 Operating Conditions
 10.4
 Periodic Measurements
 10.5
 Engine Oil Level
 10.6
 Oil Addition Procedure
 10.7
 Cool-Down Procedure
 10.8
 Shutdowns
 10.9
 Fuel System
 10.10
 Brake Specific Oil Consumption (BSOC) Calculation
 10.11
 Inspection
 11
 Preparation
 11.1
 Inspection
 11.2
 Rater Training
 11.3
 Referee Ratings
 11.4
 Calibration of Test Method
 12
 Requirements
 12.1
 Reference Oils
 12.2
 Test Numbering
 12.3
 Definition of a Test
 12.4
 New Laboratories and New Test Stands
 12.5
 Frequency of Calibration Tests
 12.6
 Specified Test Parameters
 12.10
 Acceptance of Calibration Tests
 12.11
 Failing Reference Oil Calibration Tests
 12.12
 Non-Standard Tests
 12.13
 Severity Adjustments and Control Charting
 12.14
 Test Reporting
 12.15
 Reporting Reference Results
 12.16
 Analysis of Reference Oils
 12.17
 Precision and Bias
 13
 Precision
 13.1
 Bias
 13.2
 Keywords
 14
 ANNEXES
 Figures and Schematics
 Annex A1
 Report Forms
 Annex A2
 Test Fuel Information
 Annex A3
 APPENDIXES
 Humidity Correction Factors
 Appendix X1
 Report Form Examples
 Appendix X2
 1M-PC Multiple Testing
 Appendix X3
 1.5   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM D6618-23 PDF

ASTM D6618-23 PDF

$56.50 $113.00