ASTM D6681-23 PDF

ASTM D6681-23 PDF

Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1P Test Procedure

$56.50 $113.00 -50%
Product Code: ASTM D6681
Stock In Stock
Published: 2023
Number of Pages: 57

Available Options

Product Description

Significance and Use
 5.1  This is an accelerated engine oil test, performed in a standardized, calibrated, stationary single-cylinder diesel engine that gives a measure of ( 1 ) piston and ring groove deposit forming tendency, ( 2 ) piston, ring and liner scuffing and ( 3 ) oil consumption. The test is used in the establishment of diesel engine oil specification requirements as cited in Specification D4485 for appropriate API Performance Category C oils (API 1509). The test method can also be used in diesel engine oil development.
 Scope
 1.1  This test method covers and is required to evaluate the performance of engine oils intended to satisfy certain American Petroleum Institute (API) C service categories (included in Specification D4485 ). It is performed in a laboratory using a standardized high-speed, single-cylinder diesel engine. 4 Piston and ring groove deposit-forming tendency and oil consumption is measured. The piston, the rings, and the liner are also examined for distress and the rings for mobility.
 1.2  The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
 1.2.1   Exceptions— Where there is no direct SI equivalent such as screw threads, National Pipe Threads/diameters, tubing size, or where there is a sole source supply equipment specification.
 1.3   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Being an engine test method, this standard does have definite hazards that require safe practices (see Appendix X2 on Safety).
 1.4  The following is the Table of Contents:
 Section
 Scope
 1
 Referenced Documents
 2
 Terminology
 3
 Summary of Test Method
 4
 Significance and Use
 5
 Apparatus and Installation
 6
  Intake Air System
 6.2.1
  Exhaust System
 6.2.2
  Fuel System
 6.2.3
  Oil Consumption System
 6.2.4
  Engine Oil System
 6.2.5
   Oil Heating System
 6.2.5.1
   Oil Sample Valve
 6.2.5.2
  Engine Coolant System
 6.2.6
  Engine Instrumentation
 6.2.7
 Reagents and Materials
 7
 Oil Samples
 8
 Preparation of Apparatus
 9
  General Engine Assembly Practices
 9.1
  Complete Engine Inspection
 9.2
  Copper Components
 9.3
  Engine Lubricant System Flush
 9.4
  Engine Piston Cooling Jets
 9.5
  Engine Measurements and Inspections
 9.6
  Cylinder Head
 9.7
  Valve Guide Bushings
 9.8
  Fuel Injector
 9.9
  Piston and Rings
 9.10
  Cylinder Liner
 9.11
  Compression Ratio
 9.12
  Engine Timing
 9.13
  Engine Coolant System Cleaning Procedure
 9.14
 Calibration and Standardization
 10
  Test Cell Instrumentation
 10.1
  Instrumentation Standards
 10.2
  Coolant Flow
 10.3
  Re-calibration Requirements
 10.4
  Fuel Injectors
 10.5
  Air Flow
 10.6
  Intake Air Barrel
 10.7
  Fuel Filter
 10.8
  Oil Scale Flow Rates
 10.9
  Calibration of Test Stands
 10.10
  Extending Test Stand Calibration Period
 10.11
  Test Run Numbering
 10.13
  Humidity Calibration Requirements
 10.14
  Calibration of Piston Deposit Raters
 10.15
 Procedure
 11
  Engine Break-in Procedure
 11.1
  Cool-down Procedure
 11.2
  Warm-up Procedure
 11.3
  Shutdowns and Lost Time
 11.4
  Periodic Measurements
 11.5
  Engine Control Systems
 11.6
   Engine Coolant
 11.6.1
   Engine Fuel System
 11.6.2
   Engine Oil Temperature
 11.6.3
   Exhaust Pressure
 11.6.4
   Intake Air
 11.6.5
  Post-Test Procedures
 11.7
   Piston Ring Side Clearances
 11.7.1
   Piston Ratings
 11.7.2
    Referee Ratings
 11.7.3
   Ring End Gap Increase
 11.7.4
   Cylinder Liner Wear
 11.7.5
   Cylinder Liner Bore Polish
 11.7.6
   Photographs
 11.7.7
 Calculation and Interpretation of Results
 12
  Test Validity
 12.1
  Calculations
 12.2
   Quality Index
 12.2.1
   Oil Consumption
 12.2.2
 Report
 13
  Forms and Data Dictionary
 13.1
  Test Validity
 13.2
  Report Specifics
 13.3
 Precision and Bias
 14
  Precision
 14.1
  Bias
 14.1.4
 Keywords
 15
 Annexes
 Engine and Parts Warranty
 Annex A1
 Instrument Locations, Measurements, and Calculations
 Annex A2
 Cooling System Arrangement
 Annex A3
 Intake Air Mass Flow Sensor Installation
 Annex A4
 Fuel System Design and Required Components
 Annex A5
 Oil System
 Annex A6
 Exhaust and Intake Barrel Piping
 Annex A7
 Humidity Probe Installation (Location)
 Annex A8
 Return Goods Authorization (Claim Form)
 Annex A9
 Engine Assembly Information
 Annex A10
 Flushing Instructions and Apparatus
 Annex A11
 Warm-up, Cool-down and Testing Conditions
 Annex A12
 Piston and Liner Rating Modifications
 Annex A13
 Additional Report Forms
 Annex A14
 Test Report Forms
 Annex A15
 Appendixes
 Various Examples for Reference Purposes
 Appendix X1
 Safety
 Appendix X2
 1.5   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM D6681-23 PDF

ASTM D6681-23 PDF

$56.50 $113.00