ASTM D6709-25 PDF

ASTM D6709-25 PDF

Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence VIII Spark-Ignition Engine (CLR Oil Test Engine)

$52.00 $104.00 -50%
Product Code: ASTM D6709
Stock In Stock
Published: 2025
Number of Pages: 39

Available Options

Product Description

Significance and Use
 5.1  This test method is used to evaluate automotive engine oils for protection of engines against bearing weight loss.
 5.2  This test method is also used to evaluate the SIG capabilities of multiviscosity-graded oils.
 5.3  Correlation of test results with those obtained in automotive service has not been established.
 5.4   Use— The Sequence VIII test method is useful for engine oil specification acceptance. It is used in specifications and classifications of engine lubricating oils, such as the following:
 5.4.1  Specification D4485 .
 5.4.2  API Publication 1509 Engine Oil Licensing and Certification System. 7
 5.4.3  SAE Classification J304.
 Scope
 1.1  This test method covers the evaluation of automotive engine oils (SAE grades 0W, 5W, 10W, 20, 30, 40, and 50, and multi-viscosity grades) intended for use in spark-ignition gasoline engines. The test procedure is conducted using a carbureted, spark-ignition Cooperative Lubrication Research (CLR) Oil Test Engine (also referred to as the Sequence VIII test engine in this test method) run on unleaded fuel. An oil is evaluated for its ability to protect the engine and the oil from deterioration under high-temperature and severe service conditions. The test method can also be used to evaluate the viscosity stability of multi-viscosity-graded oils. Companion test methods used to evaluate engine oil performance for specification requirements are discussed in the latest revision of Specification D4485 .
 1.2  Correlation of test results with those obtained in automotive service has not been established. Furthermore, the results obtained in this test are not necessarily indicative of results that will be obtained in a full-scale automotive spark-ignition or compression-ignition engine, or in an engine operated under conditions different from those of the test. The test can be used to compare one oil with another.
 1.3  The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
 1.3.1   Exceptions— The values stated in inch-pounds for certain tube measurements, screw thread specifications, and sole source supply equipment are to be regarded as standard.
 1.3.1.1  The bearing wear in the text is measured in grams and described as weight loss, a non-SI term.
 1.4  This test method is arranged as follows:
 Subject
 Section
 Introduction
 Scope
 1
 Referenced Documents
 2
 Terminology
 3
 Summary of Test Method
 4
 Before Test Starts
 4.1
 Power Section Installation
 4.2
 Engine Operation (Break-in)
 4.3
 Engine Operation (Test/Samples)
 4.4
 Stripped Viscosity
 4.5
 Test Completion (BWL)
 4.6
 Significance and Use
 5
 Evaluation of Automotive oils
 5.1
 Stay in Grade Capabilities
 5.2
 Correlation of Results
 5.3
 Use
 5.4
 Apparatus
 6
 Test Engineering, Inc.
 6.1
 Fabricated or Specially Prepared Items
 6.2
 Instruments and Controls
 6.3
 Procurement of Parts
 6.4
 Reagents and Materials
 7
 Reagents
 7.1
 Cleaning Materials
 7.2
 Expendable Power Section-Related Items
 7.3
 Power Section Coolant
 7.4
 Reference Oils
 7.5
 Test Fuel
 7.6
 Test Oil Sample Requirements
 8
 Selection
 8.1
 Inspection
 8.2
 Quantity
 8.3
 Preparation of Apparatus
 9
 Test Stand Preparation
 9.1
 Conditioning Test Run on Power Section
 9.2
 General Power Section Rebuild Instructions
 9.3
 Reconditioning of Power Section After Each Test
 9.4
 Calibration
 10
 Power Section and Test Stand Calibration
 10.1
 Instrumentation Calibration
 10.2
 Calibration of AFR Measurement Equipment
 10.3
 Calibration of Torque Wrenches
 10.4
 Engine Operating Procedure
 11
 Run-In and Flush
 11.1
 Test Operating Conditions
 11.2
 Air-Fuel Ratio and Spark Advance
 11.3
 Air, Off-Gas and Blowby Measurement
 11.4
 Unscheduled Shutdowns
 11.5
 Oil Sampling and Oil Addition
 11.6
 Periodic Measurements
 11.7
 Final Oil Drain and Oil Consumption Computation
 11.8
 Operational Validity Criteria
 11.9
 Test Completion
 11.10
 Determination of Test Results
 12
 Oil Analysis
 12.1
 Test Bearing Weight Loss Determination
 12.2
 Report
 13
 Precision and Bias
 14
 Precision
 14.1
 Bias
 14.2
 Use of ASTM Rounding
 15
 Keywords
 16
 ANNEXES
 ASTM Test Monitoring Center Organization
 Annex A1
 ASTM Test Monitoring Center: Calibration Procedures
 Annex A2
 ASTM Test Monitoring Center: Maintenance Activities
 Annex A3
 ASTM Test Monitoring Center: Related Information
 Annex A4
 Measurement of Connecting Rod Bearing Clearance and
 Journal Taper
 Annex A5
 Measurement of Main Bearing Clearance
 Annex A6
 Measurement of Piston-to-Sleeve Clearance
 Annex A7
 Control Chart Technique for a Laboratory's Severity
 Adjustment (SA)
 Annex A8
 Recommended New Liner Honing Procedure
 Annex A9
 Sequence VIII Oil Priming Procedure
 Annex A10
 Alternative Crankcase Breather Configuration
 Annex A11
 Connecting Rod Bearing Cleaning Procedure
 Annex A12
 Electronic Ignition Conversion
 Annex A13
 System Response Procedure
 Annex A14
 Air-Fuel Ratio Measurement
 Annex A15
 Lead Decontamination Procedure
 Annex A16
 Crankshaft Rear Seal Conditioning
 Annex A17
 Report Forms and Data Dictionary
 Annex A18
 Stay-in-Grade Oil Analysis Procedure
 Annex A19
 APPENDIXES
 Suggested Method for Salvaging Camshaft Bearing Journals
 Appendix X1
 Data Log Sheets
 Appendix X2
 1.5   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are provided throughout this test method.
 1.6   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM D6709-25 PDF

ASTM D6709-25 PDF

$52.00 $104.00