ASTM D7468-22 PDF

ASTM D7468-22 PDF

Standard Test Method for Cummins ISM Test

$52.00 $104.00 -50%
Product Code: ASTM D7468
Stock In Stock
Published: 2022
Number of Pages: 36

Available Options

Product Description

Significance and Use
 5.1  This test method was developed to assess the performance of an engine oil to control engine wear and deposits under heavy-duty operating conditions selected to accelerate soot generation, valve train wear, and deposit formation in a turbocharged, aftercooled four-stroke-cycle diesel engine equipped with exhaust gas recirculation hardware.
 5.2  This test method can be used for engine oil specification acceptance when all details of this test method are in compliance. Applicable engine oil service categories are included in Specification D4485 .
 5.3  The design of the engine used in this test method is representative of many, but not all, modern diesel engines. This factor, along with the accelerated operating conditions needs to be considered when extrapolating test results.
 Scope
 1.1  The test method covers a heavy-duty diesel engine test procedure conducted under high soot conditions to evaluate oil performance with regard to valve train wear, top ring wear, sludge deposits, and oil filter plugging in an EGR environment. This test method is commonly referred to as the Cummins ISM Test. 2
 1.2  The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
 1.2.1   Exception— The only exception is where there is no direct SI equivalent such as screw threads, national pipe threads/diameters, tubing sizes, or where there is a sole source of supply equipment specification.
 1.3   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See Annex A1 for general safety precautions.
 1.4   Table of Contents:
 Section
 Scope
 1
 Referenced Documents
 2
 Terminology
 3
 Summary of Test Method
 4
 Significance and Use
 5
 Apparatus
 6
  Test Engine Configuration
 6.1
   Test Engine
 6.1.1
   Oil Heat Exchanger, Adapter Blocks, Block Off Plate
 6.1.2
   Oil Filter Head Modification
 6.1.3
   Oil Pan Modification
 6.1.4
   Engine Control Module (ECM)
 6.1.5
   Engine Position Sensor
 6.1.6
   Intake Manifold Temperature Sensor
 6.1.7
   Barometric Pressure Sensor
 6.1.8
   Turbocharger Controller
 6.1.9
   Power Supply Voltage
 6.1.10
   Air Compressor and Fuel Pump
 6.1.11
   Engine Block Preparation
 6.1.12
  Test Stand Configuration
 6.2
   Engine Mounting
 6.2.1
   Intake Air System
 6.2.2
   Aftercooler
 6.2.3
   Exhaust System
 6.2.4
   Exhaust Gas Recirculation System
 6.2.5
   Fuel System
 6.2.6
   Coolant System
 6.2.7
   Pressurized Oil Fill System
 6.2.8
   External Oil System
 6.2.9
   Crankcase Aspiration
 6.2.10
   Blowby Rate
 6.2.11
  System Time Responses
 6.3
  Oil Sample Containers
 6.4
  Mass Balance
 6.5
 Engine and Cleaning Fluids
 7
  Test Oil
 7.1
  Test Fuel
 7.2
  Engine Coolant
 7.3
  Pentane
 7.4
  Solvent
 7.5
 Preparation of Apparatus
 8
  Cleaning of Parts
 8.1
   General
 8.1.1
   Engine Block
 8.1.2
   Cylinder Head
 8.1.3
   Rocker Cover and Oil Pan
 8.1.4
   External Oil System
 8.1.5
   Crosshead Cleaning and Measurement
 8.1.6
   Rod Bearing Cleaning and Measurement
 8.1.7
   Ring Cleaning and Measurement
 8.1.8
   Injector Adjusting Screw Cleaning and Measurement
 8.1.9
  Engine Assembly
 8.2
   General
 8.2.1
   Parts Reuse and Replacement
 8.2.2
   Build-Up Oil
 8.2.3
   Coolant Thermostat
 8.2.4
   Oil Thermostat
 8.2.5
   Fuel Injectors
 8.2.6
   New Parts
 8.2.7
  Operational Measurements
 8.3
   Units and Formats
 8.3.1
   Instrumentation Calibration
 8.3.2
   Temperatures
 8.3.3
   Pressures
 8.3.4
   Flow Rates
 8.3.5
   Intake and Exhaust CO 2 Measurement
 8.3.6
 Engine/Stand Calibration and Non-Reference Oil Tests
 9
  General
 9.1
  New Test Stand
 9.2
   New Test Stand Calibration
 9.2.1
  Stand Calibration Period
 9.3
  Stand Modification and Calibration Status
 9.4
  Test Numbering System
 9.5
   General
 9.5.1
   Reference Oil Tests
 9.5.2
   Non-Reference Oil Tests
 9.5.3
  Reference Oil Test Acceptance
 9.6
  Reference Oil Accountability
 9.7
  Last Start Date
 9.8
  Donated Reference Oil Test Programs
 9.9
  Adjustments to Reference Oil Calibration Periods
 9.10
   Procedural Deviations
 9.10.1
   Parts and Fuel Shortages
 9.10.2
   Reference Oil Test Data Flow
 9.10.3
   Special Use of the Reference Oil Calibration System
 9.10.4
 Test Procedure
 10
  Engine Installation and Stand Connections
 10.1
  Coolant System Fill
 10.2
  Oil Fill for Break-in
 10.3
   Engine Build Committed
 10.3.3
  Fuel Samples
 10.4
  Engine Warm-up
 10.5
   Shutdown During Warm-up
 10.5.1
  Engine Break-in
 10.6
  Shutdown and Maintenance
 10.7
   Normal Shutdown
 10.7.1
   Emergency Shutdown
 10.7.2
   Maintenance
 10.7.3
   Downtime
 10.7.4
  200-h Test Procedure
 10.8
   Oil Fill for Test
 10.8.2
   Operating Conditions
 10.8.4
   Injection Timing Change
 10.8.5
   Mass % Soot Validity
 10.8.6
   Test Timer
 10.8.7
   Operational Data Acquisition
 10.8.8
   Oil Sampling
 10.8.9
   Oil Addition
 10.8.10
  End of Test (EOT)
 10.9
   Engine Disassembly
 10.9.3
 Calculations, Ratings and Test Validity
 11
  Crosshead Mass Loss
 11.1
   Crosshead Mass Loss Correction Factor
 11.1.7.1
  Injector Adjusting Screw Mass Loss
 11.2
   Injector Adjusting Screw Correction Factor
 11.2.5
  Ring Mass Loss
 11.3
  Sludge Ratings
 11.4
  Oil Filter Plugging
 11.5
  Oil Analyses
 11.6
  Oil Consumption
 11.7
  Fuel Analyses
 11.8
   Additional Analysis
 11.8.1
  Assessment of Operational Validity
 11.9
  Assessment of Test Interpretability
 11.10
 Test Report
 12
  Report Forms
 12.1
  Reference Oil Test
 12.2
  Electronic transmission of Test Results
 12.2.1
 Precision and Bias
 13
  Precision
 13.1
   Intermediate Precision Conditions
 13.1.1
   Reproducibility Conditions
 13.1.2
  Bias
 13.2
 Keywords
 14
 Annexes
 Safety Precautions
 Annex A1
 Intake Air Aftercooler
 Annex A2
 Engine Build Parts Kit
 Annex A3
 Sensor Locations, Special Hardware, and Engine Block Modifications
 Annex A4
 External Oil System
 Annex A5
 Cummins Service Publications
 Annex A6
 Specified Units and Formats
 Annex A7
 Report Forms and Data Dictionary
 Annex A8
 Sludge Rating Worksheets
 Annex A9
 Oil Analyses
 Annex A10
 Determination of Operational Validity
 Annex A11
 Exhaust CO 2 Sampling Probe
 Annex A12
 ISM Merit Rating Calculation
 Annex A13
 Appendix
 Typical System Configurations
 Appendix X1
 1.5   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM D7468-22 PDF

ASTM D7468-22 PDF

$52.00 $104.00