ASTM D7528-22 PDF

ASTM D7528-22 PDF

Standard Test Method for Bench Oxidation of Engine Oils by ROBO Apparatus

$52.00 $104.00 -50%
Product Code: ASTM D7528
Stock In Stock
Published: 2022
Number of Pages: 25

Available Options

Product Description

Significance and Use
 5.1  This bench test method is intended to produce comparable oil aging characteristics to those obtained with ASTM TMC Sequence IIIGA matrix reference oils 434, 435, and 438 after aging in the Sequence IIIG engine test.
 5.2  To the extent that the method generates aged oils comparable to those from the Sequence IIIG engine test, the measured increases in kinematic and MRV viscosity indicate the tendency of an oil to thicken because of volatilization and oxidation, as in the Sequence IIIG and IIIGA (see Appendix X1 in Test Method D7320 ) engine tests, respectively.
 5.3  This bench test procedure has potential use in specifications and classifications of engine lubricating oils, such as Specification D4485 .
 5.4  The results of this test method are valid when seeking qualification of oils against published specifications only when run on a test stand that has successfully met the calibration requirements specified under the TMC’s ROBO test monitoring program.
 Scope
 1.1  This test method describes a bench procedure to simulate the oil aging encountered in Test Method D7320 , the Sequence IIIG engine test method. These aged oils are then tested for kinematic viscosity and for low-temperature pumpability properties as described in the Sequence IIIGA engine test, Appendix X1 of Test Method D7320 .
 1.2   Units— The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
 1.2.1   Exceptions— There are no SI equivalents for some apparatus in Section 6 , and there are some figures where inch units are to be regarded as standard.
 1.3  This test method is arranged as follows:
 Section
 Scope
 1
 Reference Documents
 2
 Terminology
 3
 Summary of Test Method
 4
 Significance and Use
 5
 Apparatus
 6
 Reagents and Materials
 7
 Hazards
 8
 New and Existing Test Stand Calibration
 9
 Procedure
 10
 Cleaning
 11
 Calculations and Determination of Test Results
 12
 Report
 13
 Precision and Bias
 14
 Keywords
 15
 Annexes
 ASTM Test Monitoring Center: Organization
 Annex A1
 ASTM Test Monitoring Center: Calibration Procedures
 Annex A2
 ASTM Test Monitoring Center: Maintenance Activities
 Annex A3
 ASTM Test Monitoring Center: Related Information
 Annex A4
 Reaction Vessel
 Annex A5
 Reaction Vessel Head
 Annex A6
 Reaction Vessel-to-Head Seal
 Annex A7
 Agitator Turbine Blade
 Annex A8
 Agitator Packing Gland
 Annex A9
 Nitrogen Dioxide Graduated Tube
 Annex A10
 Vacuum System Plumbing
 Annex A11
 Vacuum Trap Condensers
 Annex A12
 Setting the Vacuum Control Valve
 Annex A13
 Appendixes
 Sample Preparation and Addition
 Appendix X1
 Charging the Liquid Nitrogen Dioxide
 Appendix X2
 Nitrogen Dioxide Precision Needle Valve
 Appendix X3
 Example of an Assembled ROBO Apparatus
 Appendix X4
 Information Package to Aid Setting Up a New Robo Apparatus
 Appendix X5
 Dilute Nitrogen Dioxide in Air Option Information
 Appendix X6
 Time-Averaged Subsurface Air Flow Rate
 Appendix X7
 1.4   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific warning statements are given in Sections 7 and 8 .
 1.5   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM D7528-22 PDF

ASTM D7528-22 PDF

$52.00 $104.00