ASTM D8687-26 PDF

ASTM D8687-26 PDF

Standard Test Method for Determination of the Electric Tangential Interfacial Surface Discharge of Solid Dielectric Materials in a Liquid

$36.00 $72.00 -50%
Product Code: ASTM D8687
Stock In Stock
Published: 2026
Number of Pages: 8

Available Options

Product Description

Significance and Use
 5.1  The dielectric strength of a solid/liquid interface (herefor called “the interface” or creep surface) is of critical interest for any application where an electric field is present. The dielectric strength of this interface will be a factor in the design of the apparatus in which it will be used and will be a critical element in determining the maximum dielectric field strength and dimensional criteria of the interface.
 5.2  Tests made following this method may be used to develop applicable data to determine the withstand capabilities of the interface for use in design. It may also be used for comparing materials or deviation from expected characteristics due to processing variables and variations in manufacturing of either material involved in the interface.
 5.3  This test method is useful for design criteria, research, and process control. Results obtained by this test method can be used to develop criteria for design in the application of this material. In most cases it is necessary that these results be evaluated by comparison with results obtained not only from other functional tests or from tests on other materials, or both, along with actual known applications that have been designed and tested.
 5.4  Two methods for voltage application are defined—applied ac voltage and impulse voltage. The applied ac method may be the more commonly used since many use conversion factors converting an impulse voltage application to an equivalent ac voltage·time application. However, by use of both the ac voltage·time application along with the impulse voltage application, verification or development of conversion factors can be done.
 5.5  Documents specifying the use of this test method shall also specify:
 5.5.1  Insulation fluid to be evaluated.
 5.5.2  Solid dielectric material to be evaluated.
 Note 1:   The solid insulation applied to the U-shaped high-voltage electrode and the flat ground plane shall prevent direct contact between the conducting electrodes and the test specimen and shall minimize dielectric stress in portions of the test assembly other than the interface under evaluation. The insulating materials shall have dielectric properties, including relative permittivity and volume resistivity, reasonably similar to those of the test specimen. Selection of these materials shall be based on evaluation of their influence on the electric field and voltage distribution within the test configuration so that capacitive and resistive voltage drops occur primarily across the test specimen rather than across auxiliary insulating materials. The insulation shall provide a gradual dielectric transition between the conducting electrode and the test specimen so that dielectric stress is concentrated at the material under evaluation rather than in other regions of the test assembly.
 5.5.3  Creep distance(s) to be evaluated.
 5.5.4  Thickness of solid dielectric material to be evaluated where thickness is defined as distance perpendicular to creep distance being evaluated.
 5.5.5  Dielectric Constant/relative permittivity of all materials being tested and temperature of that test.
 5.5.6  Processing of all components involved in test.
 5.5.7  Method of voltage application, including rate of rise, initial voltage, voltage step size, number of impulses at each level, and polarity, as necessary.
 5.5.7.1  Test Method D149 :
 (1)  Method A, Short-Time Test, or
 (2)  Method B, Step-by-Step Test, or
 (3)  Method C, Slow Rate-of-Rise Test for commercial power frequencies.
 5.5.7.2  Test Method D3426 for impulse waves.
 5.5.8  Temperature of insulation fluid being evaluated during test.
 5.5.9  Electrodes (if altered for material thicker than 3.2 mm, see X1.4 ).
 5.5.10  Any deviations from the recommended procedures.
 5.6  If any of the requirements listed in 5.5 are missing from the specified documentation to this test method, then the results of this test may not be valid and the testing is not considered in conformance with this test.
 Scope
 1.1  This test method covers the determination of the tangential interfacial surface breakdown voltage, also known as interfacial surface creep breakdown, of solid insulation materials in an insulating liquid. The test procedures will include:
 1.1.1  AC line frequency.
 1.1.2  Full-wave impulse defined as 1.2 μs by 50 μs.
 1.2  The testing will determine the influence of combining solid and liquid dielectric insulation materials on the tangential interfacial surface breakdown. The solid insulation can either be impregnated or conditioned with the liquid insulation. The test procedure should include a sufficient number of determinations to provide a mean breakdown using a 50 % Gaussian distribution or a 1 % or 2 % probability of breakdown using either a two- or three-parameter Weibull distribution.
 1.3   This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
 1.4   This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
ASTM D8687-26 PDF

ASTM D8687-26 PDF

$36.00 $72.00