Testing Concrete-Methods for analysis of hardened concrete
Publishing information: This part of BS 1881 is published by BSI Standards Limited, under licence from The British Standards Institution, and came into effect on 31 August 2015. It was prepared by Subcommittee B/517/1, Concrete production and testing, under the authority of Technical Committee B/517, Concrete and related products. A list of organizations represented on these committees can be obtained on request to the committee manager. Supersession BS 1881‑124:2015+A1:2021 supersedes BS 1881‑124:2015, which is withdrawn. Relationship with other publications The BS 1881 series contains test methods for concrete currently used in the United Kingdom which are not covered by BS EN 12350, BS EN 12390 and BS EN 12504. Reference is made to the relevant part of BS EN 12350, BS EN 12390 and BS EN 12504 where appropriate. These test methods may be used in conjunction with BS EN 206. BS 1881, Testing concrete, is published in the following parts: BS 1881‑113, Method for making and curing no‑fines test cubes BS 1881‑119, Method for determination of compressive strength using portions of beams broken in flexure (equivalent cube method) BS 1881‑122, Method for determination of water absorption BS 1881‑124, Methods for analysis of hardened concrete BS 1881‑125, Methods for mixing and sampling fresh concrete in the laboratory BS 1881‑129, Method for the determination of density of partially compacted semi‑dry fresh concrete BS 1881‑130, Method for temperature‑matched curing of concrete specimens BS 1881‑131, Methods for testing cement in a reference concrete BS 1881‑204, Recommendations on the use of electromagnetic covermeters BS 1881‑206, Recommendations for determination of strain in concrete BS 1881‑207, Recommendations for the assessment of concrete strength by near‑to‑surface tests BS 1881‑208, Recommendations for the determination of the initial surface absorption of concrete BS 1881‑209, Recommendations for the measurement of dynamic modulus of elasticity BS 1881‑210, Determination of the potential carbonation resistance of concrete – Accelerated carbonation method
Information about this document: Text deleted Text introduced or altered by Amendment No. 1 is indicated in the text by tags . Minor editorial changes are not tagged. ii © THE BRITISH STANDARDS INSTITUTION 2021 – ALL RIGHTS RESERVED Amendment 1 introduces the following principle changes: Annex A has been replaced and additional tables included. Copyright is claimed on Table A.1, Table A.2, Table A.3, Table A.4 and Table A.5. The copyright holder is The Concrete Society, Riverside House, 4 Meadows Business Park, Station Approach, Blackwater, Camberley, Surrey, GU17 9AB. Hazard warnings WARNING. Where skin is in contact with fresh concrete, skin irritations are likely to occur owing to the alkaline nature of cement. The abrasive effects of sand and aggregate in the concrete can aggravate the condition. Potential effects range from dry skin and irritant contact dermatitis, to severe burns in cases of prolonged exposure. Take precautions to avoid dry cement entering the eyes, mouth and nose when mixing mortar or concrete by wearing suitable protective clothing. Take care to prevent fresh concrete from entering boots and use working methods that do not require personnel to kneel in fresh concrete. Unlike heat burns, cement burns might not be felt until sometime after contact with fresh concrete, so there might be no warning of damage occurring. If cement or concrete enters the eye, immediately wash it out thoroughly with clean water and seek medical treatment without delay. Wash wet concrete off the skin immediately. Barrier creams may be used to supplement protective clothing but are not an alternative means of protection.
Use of this document: It has been assumed in the preparation of this British Standard that the execution of its provisions will be entrusted to appropriately qualified and experienced people, for whose use it has been produced.
Presentational conventions: The provisions of this standard are presented in roman (i.e. upright) type. Its requirements are expressed in sentences in which the principal auxiliary verb is “shall”. Commentary, explanation and general informative material is presented in smaller italic type, and does not constitute a normative element. Where words have alternative spellings, the preferred spelling of the Shorter Oxford English Dictionary is used (e.g. “organization” rather than “organisation”).
Scope: This part of BS 1881 describes sampling procedures, treatment of samples and analytical methods to determine the cement content, aggregate content, aggregate grading, original water content, type of cement, type of aggregate, chloride content, sulfate content and alkali content of a sample of concrete. The procedures are applicable to concretes made with CEM I cements and, in favourable circumstances, concretes containing ground granulated blastfurnace slag (GGBS). This part of BS 1881 does not cover the analysis of concretes made with other cements and the determination of fly ash content.