ISO metric black hexagon bolts, screws and nuts. Specification
Publishing information: This British Standard is published by BSI Standards Limited, under licence from The British Standards Institution, and came into effect on 31 October 2014. It was prepared by Technical Committee FME/9, Nuts and accessories. A list of organizations represented on this committee can be obtained on request to its secretary. Supersession This British Standards supersedes BS 4190:2001, which is withdrawn. Relationship with other publications This British Standard should be read in conjunction with BS EN ISO 898-1 as it contains tables that reflect up-to-date best practice for mechanical properties of bolts.
Information about this document: The mechanical properties of the nuts in this British Standard do not conform to BS EN ISO 898-2. Higher proof load values have been allocated to the revised property classes in BS EN ISO 898-2 in order to ensure that fracture of the bolt generally occurs in the case of overloading. CAUTION. Nuts in accordance with this standard cannot be fully loaded with sufficient assurance up to the yield point of the appropriate bolt, or beyond this, without the possibility of the nut thread being stripped, and for this reason it is essential that new designs of nuts for use with BS 4190 bolts and studs conforming to this standard conform to BS EN ISO 898-2. In order to differentiate nuts that conform to this British standard from that those that conform to BS EN ISO 898-2 vertical bars have been added to the symbols for strength grade designations e.g. |8| instead of 8. It has been assumed in the preparation of this British Standard that the execution of its provisions will be entrusted to appropriately qualified and experienced people, for whose use it has been produced.
Presentational conventions: The provisions of this standard are presented in roman (i.e. upright) type. Its requirements are expressed in sentences in which the principal auxiliary verb is “shall”. Commentary, explanation and general informative material is presented in smaller italic type, and does not constitute a normative element. Requirements in this standard are drafted in accordance with Rules for the structure and drafting of UK standards, subclause J.1.1, which states, “Requirements should be expressed using wording such as: ‘When tested as described in Annex A, the product shall ...’”. This means that only those products that are capable of passing the specified test will be deemed to conform to this standard.
Scope: This standard gives the general dimensions and tolerances of black hexagon bolts, screws and nuts with ISO metric threads in diameters from 5 mm to 68 mm inclusive; basic dimensions for sizes greater than M68 are also included. This standard specifies mechanical properties of black hexagon bolts, screws and nuts made of carbon steel and alloy steel when tested at an ambient temperature range of 10 °C to 35 °C. Dimensional requirements are included for bolts, screws and nuts finished black all over and for those which have partially machined finishes. NOTE 1 Fasteners (the term used when bolts, screws and nuts are considered all together) that conform to the requirements of this standard are evaluated at this ambient temperature range. They might not retain the specified mechanical and physical properties at elevated temperatures and/or lower temperatures. This standard is not applicable to fasteners used in applications outside of the range -50 °C to +150 °C. NOTE 2 Fasteners conforming to the requirements of this standard are used in applications ranging from -50 °C to +150 °C. The use of fasteners in applications outside of this range, and up to a maximum temperature of +300 °C, might need to be based on the advice of an experienced fastener metallurgist for determining appropriate choices for a given application. NOTE 3 Nuts in accordance with this standard cannot be fully loaded with sufficient assurance up to the yield point of the appropriate bolt, or beyond this, without the possibility of the nut thread being stripped, and for this reason it is essential that new designs of nuts for use with BS 4190 bolts and studs conforming to this standard conform to BS EN ISO 898-2. NOTE 4 Nuts with an effective height of less than 0.6d and/or with a width across flats or outside diameter of less than 1.4d are excluded from the mechanical requirements specified. The dimensional requirements of this British Standard are also applicable to non-ferrous and stainless steel b
Contents:
- Foreword
- Scope
- Annexes
- Annex A (normative) Testing of mechanical properties of steel nuts
- Annex B (normative) Basic dimensions for sizes greater than 68 mm
- Annex C (informative) Manufacturers’ recommended range of sizes
- Annex D (informative) Strength grade designation system for steel bolts and
- Bibliography