Code of practice for the safe use of cranes-Inspection, maintenance and thorough examination. Cargo handling and container cranes
Publishing information: This sub-part of BS 7121-2 is published by BSI Standards Limited, under license from the British Standards Institution and came into effect on 30 September 2013. It was prepared by Subcommittee MHE/3/11, Crane safety and testing, under the authority of Technical Committee MHE/3, Cranes and derricks. A list of organizations represented on these committees can be obtained on request to their secretary. Relationship with other publications The BS 7121 series is being revised. The following new sub-parts of BS 7121-2 have been published or are in preparation. Part 2-1: Inspection, maintenance and thorough examination – General; Part 2-3: Inspection, maintenance and thorough examination – Mobile cranes; Part 2-4: Inspection, maintenance and thorough examination – Loader cranes; Part 2-5: Inspection, maintenance and thorough examination – Tower cranes; Part 2-7: Inspection, maintenance and thorough examination – Overhead travelling cranes including portal and semi-portal cranes, hoists, and their supporting structures; Part 2-9; Inspection, maintenance and thorough examination – Cargo handling and container cranes. When all sub-parts of BS 7121-2 have been published, it is intended that CP 3010 will be withdrawn and BS 5744 will be revised to cover manually operated and light cranes only. This sub-part of BS 7121-2 is intended to be used in conjunction with
Information about this document: The Health and Safety Executive (HSE) commends the use of this British Standard to those who have duties under the Health and Safety at Work etc. Act 1974 [1]. This standard was drawn up with the participation of HSE representatives and it will be referred to in the relevant HSE publications. The BS 7121-2 series has been accepted by the HSE as representing the consensus of opinion based on practical experience for safety of cranes. Hazard warnings WARNING. This British Standard calls for the use of procedures that can be injurious to health if adequate precautions are not taken. It refers only to technical suitability and does not absolve the user from legal obligations relating to health and safety at any stage.
Use of this document: As a code of practice, this sub-part of BS 7121-2 takes the form of guidance and recommendations. It should not be quoted as if it were a specification and particular care should be taken to ensure that claims of compliance are not misleading. Any user claiming compliance with this sub-part of BS 7121-2 is expected to be able to justify any course of action that deviates from its recommendations. It has been assumed in the preparation of this British Standard that the execution of its provisions will be entrusted to appropriately qualified and experienced people, for whose use it has been produced.
Presentational conventions: The provisions of this standard are presented in roman (i.e. upright) type. Its recommendations are expressed in sentences in which the principal auxiliary verb is “should”. Commentary, explanation and general informative material is presented in smaller italic type, and does not constitute a normative element.
Scope: This sub-part of BS 7121-2 gives recommendations for the pre-use checks, in-service inspection, maintenance, thorough examination (in service and following exceptional circumstances) and supplementary testing of cargo handling and container cranes used in ports and inland facilities. This sub-part of BS 7121-2 is applicable to the following types of cranes: ship to shore or quay cranes; slewing jib cranes, including mobile harbour cranes; level luffing slewing jib cranes; rail mounted gantry cranes; rubber tyred gantry cranes; straddle carrier cranes; scotch derricks; boat hoists. This sub-part of BS 7121-2 also covers lifting attachments for use in conjunction with the cranes, including container spreaders, overheight frames, rotators, grabs, magnets and crane baskets used to access containers on ships. This sub-part of BS 7121-2 is not applicable to permanently installed cranes on marine and other water-borne vessels. This sub-part of BS 7121-2 is not applicable to loader cranes permanently installed on quays or in other static locations (see BS 7121-2-4).
Contents:
- Foreword
- Introduction
- Scope
- Annexes
- Annex A (informative) Container cranes – Examples of checklists for pre-use
- Annex B (informative) Mobile harbour cranes – Examples of checklists for
- Annex C (informative) Straddle carrier cranes and rubber tyred gantry cranes –
- Annex D (informative) Level luffing and slewing jib cranes – Examples of
- Annex E (informative) Crane container top safety frames (man riding cages) used
- Annex F (informative) Container spreaders – Examples of checklists for pre-use
- Bibliography