Examination and test of new lifts before putting into service. Specification for means of determining compliance with BS EN 81-Lift features for emergency recall conforming to BS EN 81-73
Publishing information: This part of BS 8486 is published by BSI Standards Limited, under licence from The British Standards Institution, and came into effect on 30 April 2018. It was prepared by Technical Committee MHE/4, Lifts, hoists and escalators. A list of organizations represented on this committee can be obtained on request to its secretary. Relationship with other publications BS 8486 is expected to be published in a number of parts: Part 1: Electric lifts (covering lifts conforming to BS EN 81‑1); Part 2: Hydraulic lifts (covering lifts conforming to BS EN 81‑1); Part 3: Passenger and goods passenger lifts conforming to BS EN 81‑20; Part 4: Passenger and goods passenger lifts in existing buildings conforming to BS EN 81‑211; Part 5: Lift alarm systems conforming to BS EN 81‑281; Part 6: Lift features for accessibility conforming to BS EN 81‑701; Part 7: Lift features for vandalism conforming to BS EN 81‑711; Part 8: Lift features for fire‑fighting conforming to BS EN 81‑72; Part 9: Lift features for emergency recall conforming to BS EN 81‑73; Part 10: Lift features for evacuation conforming to BS EN 81‑761. This part of BS 8486 is intended to be read in conjunction with BS EN 81‑73:2016.
Information about this document: BS EN 81‑73:2005 will be withdrawn on 31 August 2018 and replaced with BS EN 81‑73:2016. BS 8486‑9 is intended to be used as a means to verify conformity to BS EN 81‑73:2016. BS 8486‑1 and BS 8486‑2 will remain available for testing lifts installed in accordance with BS EN 81‑73:2005. The Lifts Regulations 2016 [1] require the installer of a lift to take responsibility for its design, manufacture, installation and placing upon the market. For conformity assessment, the Lifts Regulations 2016 [1] require that before placing upon the market and putting into service a lift shall have undergone certain procedures including inspection and test. The inspection and test procedures may be undertaken by the installer provided that: the installer can demonstrate the necessary expertise by having an appropriate quality assurance system; and either the lift conforms to a harmonized standard; or the lift has a Type Examination Certificate or Design Examination Certificate from a Notified Body. According to the requirements of the Lifts Regulations 2016 [1], the competence of the persons carrying out the testing of a lift needs to be confirmed. This can be demonstrated if they operate in Intended for future publication. ii © THE BRITISH STANDARDS INSTITUTION 2018 – ALL RIGHTS RESERVED accordance with a quality assurance system. In the case of installers, this can be in accordance with a quality assurance system, monitored by a Notified Body. NOTE Notified Bodies testing lift installations are expected to use the test report produced by the NBL Forum. This part of BS 8486 specifies a means of determining compliance with BS EN 81‑73. It does not cover every clause in BS EN 81‑73, as many requirements are covered by the installer’s quality control procedures or are to be verified by the building designer.
Use of this document: It has been assumed in the preparation of this British Standard that the execution of its provisions will be entrusted to appropriately qualified and experienced people, for whose use it has been produced. Attention is particularly drawn to the recommendations for safe working practices provided in BS 7255. Whilst BS 7255 was written to cover the hazards which can be encountered when a lift is undergoing regular maintenance, much of its content is equally applicable to the hazards found during the testing process. BSI permits the reproduction of the tables in this part of BS 8486. This reproduction is only permitted where it is necessary for the user to record findings on the tables during each application of the standard. It is assumed that manufacturers and installers will customize these tables to suit their product range, if necessary by removing questions which are not relevant to the lift to be tested. The following documents are required for the examination and tests to be carried out: installation and test instructions; general arrangement drawings; electrical schematic drawings; copies of test certificates (including Type Examination Certificates and details to allow safety component verification); Notified Body approvals (if applicable) such as Type Examination Certificates and Design Examination Certificates. This document is not applicable to existing lifts (installed to previous standards), although it may be used to record the examinations and tests where fire recall operation has been added to an existing lift.
Presentational conventions: The provisions of this standard are presented in roman (i.e. upright) type. Its requirements are expressed in sentences in which the principal auxiliary verb is “shall”. Commentary, explanation and general informative material is presented in smaller italic type, and does not constitute a normative element. Where words have alternative spellings, the preferred spelling of the Shorter Oxford English Dictionary is used (e.g. “organization” rather than “organisation”). It is recognized that certain tests/checks can be carried out more effectively before installation, and that others should only be made on site, unless it can be demonstrated by a quality assurance procedure and risk assessment that they can be performed with equal effectiveness off site. Answer boxes in this part of BS 8486 that contain a shaded square imply that the test should be carried out on site as part of installation or testing. BRITISH STANDARD
Scope: This part of BS 8486 specifies one means of determining compliance with the provisions for examination, testing and recording results for the behaviour of lifts in the event of fire specified in BS EN 81‑73:2016, before being put into service.