BS 1722-12-2016 PDF

BS 1722-12-2016 PDF

Fences-Steel palisade fences. Manufacturing and installation. Specification

$172.72 $345.44 -50%
Publisher
isbn 9780580904981
Product Code: BS 1722-12
Stock In Stock
Published: 09/30/2016
Number of Pages: 44
File Size: 1 file, 1.5 MB

Available Options

Product Description

Fences-Steel palisade fences. Manufacturing and installation. Specification

Publishing information: This British Standard is published by BSI Standards Limited, under licence from The British Standards Institution, and came into effect on 30 September 2016. It was prepared by Technical Committee B/201, Fences and gates. A list of organizations represented on this committee can be obtained on request to its secretary. Supersession This British Standard supersedes BS 1722-12:2006, which is withdrawn. Relationship with other publications BS 1722, Steel palisade fences, is published in the following parts: Part 1: Specification for chain link fences; Part 2: Specification for strained wire and wire mesh netting fences; Part 4: Specification for cleft chestnut pale fences; Part 5: Specification for close-boarded and wooden palisade fences; Part 7: Specification for wooden post and rail fences; Part 8: Specification for mild steel (low carbon steel) continuous bar fences and hurdles; Part 9: Specification for mild steel (low carbon steel) fences with round or square verticals and flat horizontals; Part 10: Specification for anti-intruder fences in chain link and welded mesh; Part 11: Specification for prefabricated wood panel fences; Part 12: Steel palisade fences – Manufacturing and installation – Specification; Part 14: Specification for open mesh steel panel fences; Part 16: Specification for powder coatings used as a plastics finish to components and mesh; Part 17: Specification for electric security fences – Design, installation and maintenance; Part 18: Specification for free-standing temporary steel mesh perimeter fencing panels.

Information about this document: This is a full revision and introduces additional factors in gate safety and component performance requirements. The British Standard has also been arranged to make clear the principal responsibility for meeting the requirements of each section between manufacturer and installer. It is generally assumed in the preparation of this British Standard that the fence is installed in level, normal ground conditions.

Use of this document: It has been assumed in the preparation of this British Standard that the execution of its provisions will be entrusted to appropriately qualified and experienced people. At the time of publication two appropriate qualification schemes are available: the Fencing Industry Skills Scheme (FISS) and the Construction Skills Certification Scheme (CSCS). 1) FISS/CSCS maintain a national register for fence installers and operatives. Other schemes might be available.

Presentational conventions: The provisions of this British Standard are presented in roman (i.e. upright) type. Its requirements are expressed in sentences in which the principal auxiliary verb is “shall”. Commentary, explanation and general informative material is presented in smaller italic type, and does not constitute a normative element. Requirements in this British Standard are drafted in accordance with Rules for the structure and drafting of UK standards, subclause J.1.1, which states, “Requirements should be expressed using wording such as: ‘When tested as described in Annex A, the product shall ...’”. This means that only those products that are capable of passing the specified test will be deemed to conform to this British Standard.

Scope: This part of BS 1722 specifies requirements for steel palisade fences and gates for general purpose (GP) fences for heights up to 2.4 m, and for security purpose (SP) fences for heights of 3 m and 3.6 m, all with posts at 2.75 m centres. This British Standard also covers fences between 2.4 m and 3 m in height with components constructed to the SP specification. NOTE 1 Where greater resistance against penetration is required for fences below 2.4 m in height, the SP components should be obtained from the purchaser. NOTE 2 Requirements in this British Standard for the minimum sizes of fence components are based on a design wind loading, q, at right angles to the plane of the fence of 900 N/m2 employing a shape factor of 1.9 on the net area presented to the wind. NOTE 3 In situations of extreme exposure or abnormal loading, a special appraisal should be undertaken and the design criteria should be obtained from the purchaser. NOTE 4 The responsibility for ensuring the final installation meets this British Standard belongs to the installer. This responsibility can be mitigated by obtaining certificates for materials used from the suppliers (see Clause 10).

Contents:

  • Foreword
  • Scope
  • Annexes
  • Annex A (normative) Method for the determination of characteristic flexural
  • Annex B (normative) Method for the determination of characteristic flexural
  • Annex C (normative) Method for the determination of characteristic flexural
  • Annex D (normative) Method of determination of tensile strength of cold
  • Annex E (normative) Method of determination of the strength of the pale to
  • Annex F (informative) Specifying a steel palisade fence
  • Bibliography

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
BS 1722-12-2016 PDF

BS 1722-12-2016 PDF

$172.72 $345.44