BS 6400-1-2016 PDF

BS 6400-1-2016 PDF

Specification for installation, exchange, relocation, maintenance and removal of gas meters with a maximum capacity not exceeding 6 m3/h-Low pressure (2nd family gases)

$204.47 $408.94 -50%
Publisher
isbn 9780580827747
Product Code: BS 6400-1
Stock In Stock
Published: 06/30/2016
Number of Pages: 52
File Size: 1 file, 1.6 MB

Available Options

Product Description

Specification for installation, exchange, relocation, maintenance and removal of gas meters with a maximum capacity not exceeding 6 m3/h-Low pressure (2nd family gases)

Publishing information: This part of BS 6400 is published by BSI Standards Limited, under licence from The British Standards Institution, and came into effect on 30 June 2016. It was prepared by Technical Committee GSE/30, Gas installations (1st, 2nd and 3rd family gases). A list of organizations represented on this committee can be obtained on request to its secretary. Supersession BS 6400:2016 supersedes BS 6400-1:2006, which is withdrawn. Relationship with other publications BS 6400, Specification for installation, exchange, relocation, maintenance and removal of gas meters with a maximum capacity not exceeding 6m3/h, is published in three parts: Part 1: Low pressure (2nd family gases); Part 2: Medium pressure (2nd family gases); Part 3: Low and medium pressure (3rd family gases). Terminology in this part of BS 6400 might not necessarily be consistent with BS 6400-3, which uses terminology that is consistent with that used in the liquefied petroleum gas industry. This standard has been prepared as a supporting document to COP/1a, the Ofgas code of practice for low pressure meter installations with capacities not exceeding 6 m³/h [1].

Information about this document: This is a full revision of the standard to bring it up to date and to include a new clause on maintenance. Hazard warnings WARNING. This British Standard calls for the use of substances and/or procedures that can be injurious to health if adequate precautions are not taken. It refers only to technical suitability and does not absolve the user from legal obligations relating to health and safety at any stage.

Use of this document: It has been assumed in the preparation of this British Standard that the execution of its provisions will be entrusted to appropriately qualified and experienced people, for whose use it has been produced.

Presentational conventions: The provisions of this standard are presented in roman (i.e. upright) type. Its requirements are expressed in sentences in which the principal auxiliary verb is “shall”. Commentary, explanation and general informative material is presented in smaller italic type, and does not constitute a normative element.

Scope: This British Standard specifies requirements for the installation, exchange, relocation, maintenance and removal of credit or prepayment diaphragm and ultrasonic gas meters with a maximum capacity not exceeding 6 m³/h. NOTE 1 For the purposes of this British Standard, installation includes design, inspection and commissioning. It is recognized that each of these tasks can be performed by the same person. This part of BS 6400 is applicable to primary and secondary meter installations: a) supplied with 2nd family gases from low pressure gas distribution systems with a maximum operating pressure not exceeding 75 mbar, a design minimum pressure of 19 mbar and a design maximum incidental pressure of 200 mbar; b) fitted downstream of the emergency control valve; c) that utilize a primary meter regulator downstream of the emergency control valve; d) where the operating pressure at the outlet of the meter is nominally 21 mbar. 1) NOTE 2 Low pressure gas networks in Great Britain operate with a maximum operating pressure not exceeding 75 mbar, a design minimum pressure of 19 mbar and a design maximum incidental pressure of 200 mbar. NOTE 3 Installation pipework is specified in BS 6891. NOTE 4 Service pipes (including the emergency control valve) are specified in the Institution of Gas Engineers and Managers’ publication on gas services, IGE/TD/4 [18]. NOTE 5 All pressures quoted in this standard are gauge pressures and all pressure absorption values are for natural gas unless otherwise specified. NOTE 6 Additional guidance on domestic gas systems can be found in BS EN 1775, NOTE 7 Additional guidance on gas installations in multi-occupancy buildings is given in IGEM/G/5 [N7].

Contents:

  • Foreword
  • Scope
  • Annexes
  • Annex A (normative) Determination of required maximum capacity of a meter
  • Bibliography

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
BS 6400-1-2016 PDF

BS 6400-1-2016 PDF

$204.47 $408.94