BS 7608-2014+A1-2015 PDF

BS 7608-2014+A1-2015 PDF

Guide to fatigue design and assessment of steel products

$220.98 $441.96 -50%
Publisher
isbn 9780580915406
Product Code: BS 7608
Stock In Stock
Published: 12/31/2015
Number of Pages: 152
File Size: 1 file, 1.6 MB

Available Options

Product Description

Guide to fatigue design and assessment of steel products

Publishing information: This British Standard is published by BSI Standards Limited, under licence from The British Standards Institution, and came into effect on 31 March 2014. It was prepared by Technical Committee WEE/37, Acceptance levels for flaws in welds. A list of organizations represented on this committee can be obtained on request to its secretary. Supersession BS 7608:2014+A1:2015 supersedes BS 7608:2014, which is withdrawn.

Information about this document: Guidance on general fatigue design philosophy is given in Annex A, which also contains a brief description of the method of using this British Standard. A more general method for assessing welded joints using the hot-spot stress, only included previously for assessing tubular joints, is also included. The relevant application standard or specification for the particular product being assessed specifies the following: a) the loading to be assumed for design purposes, including its magnitude and frequency; b) the required life of the structure; c) the environmental conditions; d) the required nominal probability of failure. BS 7608:2014 was a full revision of the standard, and introduced the following principal changes [1]: Introduction of the hot-spot stress method with guidance on finite element stress analysis (FEA). New correction for both plate thickness and applied bending with allowance for welded joint proportions. Additional weld details; some have been reclassified. Weld quality requirements based on fitness for purpose. Revised sea water corrosion fatigue data. New rules for bolts. Design data to resist shear fatigue failure. Guidance on stress calculation for combined loading. Revised cumulative damage rules. Comprehensive guidance on use of weld toe improvement methods. New guidance on acceptance fatigue testing and statistical analysis of results. European standards containing fatigue rules for steel structures and pressure vessels have been published since the 1993 edition of this British Standard. It is therefore not applicable to product areas covered by them. It is applicable to a wide range of other steel product areas that do not have specific fatigue rules. Text introduced or altered by Amendment No. 1 is indicated in the text by tags . Minor editorial changes are not tagged. The principal changes are to Table 4 to Table 10, Clause 14, Clause 16, Table 18, new Table 21, Annex C and Annex F.

Use of this document: As a guide, this British Standard takes the form of guidance and recommendations. It should not be quoted as if it were a specification or a code of practice and claims of compliance cannot be made to it.

Presentational conventions: The guidance in this standard is presented in roman (i.e. upright) type. Any recommendations are expressed in sentences in which the principal auxiliary verb is “should”. Commentary, explanation and general informative material is presented in smaller italic type, and does not constitute a normative element.

Scope: 1.1 General This British Standard gives methods for assessing the fatigue life of parts of steel products that are subject to repeated fluctuations of stress. It is applicable to all areas of industrial application that are not covered by other British Standards containing fatigue assessment rules. NOTE Some British Standards have specific product acceptance tests for fatigue life, but do not have assessment rules. In such cases the guidance in this British Standard might be applicable for product development purposes. 1.2 Applications not covered This British Standard is not applicable to the following application areas; a) lighting columns (see BS EN 40); b) concrete building and civil engineering structures (see BS EN 1992); c) steel building and civil engineering structures [see BS EN 1993 (all parts)]; d) composite steel and concrete building and civil engineering structures [see e) unfired pressure vessels (see BS EN 13445); and f) fixed offshore structures (see BS EN ISO 19902). 1.3 Materials This British Standard covers: a) wrought steel material products; b) welds in fully machined areas of steel casting; c) ferritic alloy and low alloy steels; d) austenitic and duplex stainless steels; e) unprotected weathering steels; and f) threaded fasteners. It is applicable to yield strengths in the range 200 N/mm2 to 960 N/mm2 and ultimate tensile strengths in the range 360 to 1 200 N/mm2 for material thicknesses 3 mm and greater. This British Standard is not applicable to the following: 1) proprietary fasteners; 2) steel castings; 3) cold drawn products; 4) wire ropes; and 5) steel for reinforcement in concrete. 1.4 Manufacturing processes This British Standard is applicable to machined products with the following exceptions: a) rough sawn surfaces; b) surfaces requiring high quality surface finish (e.g. lapping, polishing, honing, fine grinding); and

Contents:

  • Foreword
  • Scope
  • Annexes
  • Annex A (normative) Fatigue design
  • Annex B (normative) Explanatory notes on detail classification
  • Annex C (normative) Guidance on stress analysis
  • Annex D (normative) Guidance on the use of fracture mechanics
  • Annex E (normative) Fatigue testing and the use of test data to define design
  • Annex F (normative) Weld toe improvement techniques
  • Annex G (normative) Assessment of tubular node joints
  • Annex H (normative) Cycle counting by the reservoir method
  • Bibliography

Be the first to write a review for this product.

Write a review

Note: HTML is not translated!
Bad           Good
BS 7608-2014+A1-2015 PDF

BS 7608-2014+A1-2015 PDF

$220.98 $441.96