Examination and test of new lifts before putting into service. Specification for means of determining compliance with BS EN 81-Passenger and goods passenger lifts conforming to BS EN 81-20
Publishing information: This part of BS 8486 is published by BSI Standards Limited, under licence from The British Standards Institution, and came into effect on 31 October 2017. It was prepared by Technical Committee MHE/4, Lifts, hoists and escalators. A list of organizations represented on this committee can be obtained on request to its secretary. Relationship with other publications BS 8486 is expected to be published in ten parts: Part 1: Electric lifts (covering lifts conforming to BS EN 81-1); Part 2: Hydraulic lifts (covering lifts conforming to BS EN 81-2); Part 3: Passenger and goods passenger lifts conforming to BS EN 81‑20; Part 4: Passenger and goods passenger lifts in existing buildings conforming to BS EN 81‑211; Part 5: Lift alarm systems conforming to BS EN 81-281; Part 6: Lift features for accessibility conforming to BS EN 81-701; Part 7: Lift features for vandalism conforming to BS EN 81-711; Part 8: Lift features for fire-fighting conforming to BS EN 81-721; Part 9: Lift features for emergency recall conforming to BS EN 81‑731; Part 10: Lift features for evacuation conforming to BS EN 81-761. This part of BS 8486 is intended to be read in conjunction with BS EN 81‑20:2014.
Information about this document: BS EN 81-1 and BS EN 81-2 were withdrawn on 31 August 2017 and replaced with BS EN 81‑20 and BS EN 81-50. BS 8486‑3 is intended to be used as a means to verify conformity with BS EN 81‑20. BS 8486‑1 and BS 8486‑2 will remain available for testing lifts installed in accordance with Due to the changes in technology since the first publication of BS EN 81‑1, certain types of lift are no longer found to be in common use. For this reason, the following types of lift drive mechanisms, whilst previously included in BS EN 81‑1 and present to some extent in BS EN 81-20, are excluded from the scope of this part of BS 8486: a) positive drive lifts by use of drum and ropes; b) positive drive lifts by use of sprocket and chains; c) rack and pinion lifts conforming to DD 222. The Lifts Regulations 2016 [1] require the installer of a lift to take responsibility for its design, manufacture, installation and placing upon the market. For conformity assessment, the Lifts Regulations 2016 [1] require that before placing upon the market and putting into service a lift shall have undergone certain procedures including inspection and test. Intended for future publication. ii © THE BRITISH STANDARDS INSTITUTION 2017 – ALL RIGHTS RESERVED The inspection and test procedures may be undertaken by the installer provided that: 1) the installer can demonstrate the necessary expertise by having an appropriate quality assurance system; and either 2) the lift conforms to a harmonized standard; or 3) the lift has a Type Examination Certificate or Design Examination Certificate from a Notified Body. According to the requirements of the Lifts Regulations 2016 [1], in order for the installer to demonstrate the competence of the persons carrying out the testing of the lift it is necessary that they operate in accordance with a quality assurance system, monitored by a Notified Body. It might be necessary to make available certification of the quality assurance system in order to prove compliance with the Lifts Regulations. NOTE Notified Bodies testing lift installations are expected to use the test report produced by the NBL Forum. This part of BS 8486 specifies a means of determining compliance with BS EN 81‑20. It does not cover every clause in BS EN 81‑20 as many requirements are covered by the installer’s quality control procedures. This part of BS 8486 covers the tests in BS EN 81-20:2014, Clause 6, as well as tests that do not fall within the installer’s quality control system; for example, the depth of the pit to ensure conformity to arrangement drawings. This part of BS 8486 does not cover other issues that are part of the installer’s quality assurance system such as calibration of mechanical and electrical test equipment used in the specified tests [e.g. force measurements (N), energy measurements (J), tachometers, voltmeters, ammeters, etc.].
Scope: This part of BS 8486 specifies one means of determining compliance with the provisions for examination, testing and recording results for new electric and hydraulic lifts specified in BS EN 81‑20:2014, before being put into service. This part of BS 8486 does not cover the following types of lift or lift equipment: a) positive drive lifts by use of drum and ropes; b) positive drive lifts by use of sprocket and chains; c) rack and pinion lifts conforming to DD 222; d) variations from BS EN 81-20 which might have been approved under design examination schemes by Notified Bodies. Whilst PESSRAL is included within the scope of this part of BS 8486, it is limited to the recording of the use of the equipment and not its testing methodology. The method of testing and proving compliance of such equipment is expected to be provided by the manufacturer. BRITISH STANDARD