Specification for repairs to tyres for motor vehicles used on the public highway
Publishing information: This British Standard is published by BSI Standards Limited, under licence from The British Standards Institution, and came into effect on 30 November 2013. It was prepared by Technical Committee AUE/3, Renovation of tyres for motor vehicles. A list of organizations represented on this committee can be obtained on request to its secretary. Supersession This British Standard supersedes BS AU 159f:1997, which is withdrawn.
Information about this document: Repairs for limited run-flat tyres and temporary use spare tyres are not covered by this British Standard. Repairs to inner tubes are covered, but repairs for commercial vehicle steel diagonal ply tyres are not, as this type of tyre is considered obsolete. The 1973 edition of this British Standard specified the use of an inner tube to repair very small penetrations in tubeless tyres. This method is not specified in the 1981, 1990, 1997 editions or the present edition. Good workshop practice for tyre repair is included in this British Standard, with emphasis on conditions during vulcanizing to ensure that carcasses are cured in the relaxed shape.
Presentational conventions: The provisions of this standard are presented in roman (i.e. upright) type. Its requirements are expressed in sentences in which the principal auxiliary verb is “shall”. Commentary, explanation and general informative material is presented in smaller italic type, and does not constitute a normative element. Requirements in this standard are drafted in accordance with The BSI guide to standardization – Section 2: Rules for the structure, drafting and presentation of British Standards, subclause 11.3.1, which states, “Requirements should be expressed using wording such as: ‘When tested as described in Annex A, the product shall ...’”. This means that only those products that are capable of passing the specified test will be deemed to conform to this standard.
Scope: This British Standard specifies requirements for the repair of diagonal ply and radial ply pneumatic tyres for motorcycles, scooters, cars, commercial and agricultural vehicles for use on the public highway. It specifies inspection procedures, performance criteria, repair materials, and marking requirements, for both tubed and tubeless tyres. The repair of tubes and inflation valves is also covered. This British Standard is not applicable to: a) tyres designed for use on pre-1933 vehicles, as their design and construction can be unique and outside the range of tyres in current use; b) T-type temporary use spare tyres; c) temporary seals, i.e. externally inserted plugs, intended to allow the vehicle to be driven for a limited period, until a permanent repair can be effected; d) use of liquid sealants introduced into tubed or tubeless tyres to aid the air retention property (see Clause 9); e) tyres containing sealant gel; and f) specialist repairs carried out by the original tyre manufacturer. Terms and definitions For the purposes of this British Standard, the following definitions apply. NOTE Figure 1 to Figure 7 supplement the definitions given in this clause. 2.1 Structure 2.1.1 bias-belted tyre pneumatic tyre of the diagonal ply type, with the carcass restricted by a belt comprising two or more layers of inextensible cord material laid at alternate angles not greater than those of the carcass NOTE For the purposes of this British Standard, a bias-belted tyre may be treated as a diagonal ply tyre. 2.1.2 diagonal ply tyre pneumatic tyre in which the ply cords extend to the bead and lie at alternate angles substantially less than 90° to the centreline of the tread NOTE Also known as cross ply tyre. NOTE The angle varies between manufacturers and applications. 2.1.3 radial ply tyre pneumatic tyre in which the ply cords extend to the bead and lie at approximately 90° to the centreline of the tread, the carcass stabilized by an essentially inextensible circumferential
Contents:
- Foreword
- Scope
- Annexes
- Annex A (normative) Initial inspection
- Annex B (normative) Minor repairs to radial ply tyres for cars, commercial and
- Annex C (normative) Limits on or repairs for radial car tyres
- Annex D (normative) Limits on major repairs for radial ply tyres for commercial
- Annex E (normative) Limits on repairs for radial ply tyres for agricultural
- Annex F (normative) Minor repairs to diagonal ply tyres for cars, commercial and
- Annex G (normative) Limits on repairs for diagonal ply car tyres
- Annex H (normative) Limits on major repairs for diagonal ply tyres for
- Annex I (normative) Limits on repairs for Diagonal ply tyres for agricultural
- Annex J (normative) Limits on minor repairs for motorcycle and scooter
- Annex K (normative) Tyre repair preparation and building
- Annex L (normative) Vulcanization
- Annex M (normative) Repairs to inner tubes and inflation valves
- Annex N (informative) Calculated values of repairable area of area T based on