Asphalt. Guidance on the use of BS EN 12697 “Bituminous mixtures. Test methods”
Publishing information: This Publish Document is published by BSI Standards Limited, under licence from The British Standards Institution, and came into effect on 30 April 2018. It was prepared by Subcommittee B/510/1, Asphalt products, under the authority of Technical Committee B/510, Road materials. A list of organizations represented on these committees can be obtained on request to their secretary. Supersession This Published Document supersedes PD 6692:2006, which is withdrawn. Relationship with other publications This Published Document gives guidance on the use and application of a series of European Standards for asphalt. These European Standards were prepared by CEN/TC 227/WG1, Bituminous Materials, and have been adopted as British Standards. PD 6692 also gives guidance on the use of the various parts of BS EN 12697, Bituminous mixtures – Test methods for hot mix asphalt, prepared by CEN/TC 227/WG1/TG2, that specify test methods for asphalt. Guidance on the various parts of BS EN 13108, Bituminous mixtures – Material specifications, is given in PD 6691.
Use of this document: As a guide, this Published Document takes the form of guidance and recommendations. It should not be quoted as if it were a specification or a code of practice and claims of compliance cannot be made to it.
Presentational conventions: The guidance in this Published Document is presented in roman (i.e. upright) type. Any recommendations are expressed in sentences in which the principal auxiliary verb is “should”. Commentary, explanation and general informative material is presented in smaller italic type, and does not constitute a normative element. Where words have alternative spellings, the preferred spelling of the Shorter Oxford English Dictionary is used (e.g. “organization” rather than “organisation”).
Scope: Table 1 — Asphalt tests in BS EN 12697 called up in asphalt specifications BS EN 13108 Overview of European Standards defining test methods for asphalts 2.1 “Back of the lorry” 2.2 CE marking 2.3 Status of tests 2.4 Empirical and fundamental tests Guidance on test methods required for testing the constituent materials 3.1 3.2 BS EN 12697‑2 — Determination of particle size distribution 3.3 BS EN 12697‑3 — Bitumen recovery: rotary evaporator 3.4 BS EN 12697‑4 — Bitumen recovery: fractionating column 3.5 BS EN 12697‑5 — Determination of the maximum density 3.6 BS EN 12697‑6 — Determination of bulk density of bituminous specimens 3.7 BS EN 12697‑7 — Determination of the bulk density of bituminous specimens by gamma rays 3.8 BS EN 12697‑8 — Determination of void characteristics of bituminous specimens 3.9 BS EN 12697‑9 — Determination of the reference density 3.10 3.11 BS EN 12697‑11 — Determination of the affinity between aggregate and bitumen 3.12 BS EN 12697‑12 — Determination of the water sensitivity of bituminous specimens 3.13 BS EN 12697‑13 — Temperature measurement 3.14 3.15 BS EN 12697‑15 — Determination of the segregation sensitivity 3.16 BS EN 12697‑16 — Abrasion by studded tyres 3.17 BS EN 12697‑17 — Particle loss of porous asphalt specimens 3.18 3.19 BS EN 12697‑19 — Permeability of specimen 3.20 BS EN 12697‑20 — Indentation using cube or cylindrical specimens 3.21 BS EN 12697‑21 — Indentation using plate specimens 3.22 3.23 BS EN 12697‑23 — Determination of the indirect tensile strength of bituminous specimens 3.24 3.25 BS EN 12697‑25 — Cyclic compression test 3.26 3.27 Table 2 — Recommended mass of bulk sample 3.28 BS EN 12697‑28 — Preparation of samples for determining binder content, water content and grading 3.29 BS EN 12697‑29 — Determination of the dimensions of a bituminous specimen 3.30 BS EN 12697‑30 — Specimen preparation by impact compactor 3.31 BS EN 12697‑31 — Specimen preparation by gyratory compactor 3.32 BS EN 12697‑32 — Laboratory compactio